Transfer supports for transfer surfaces complying with M301.2.3.1 and M305.2.2.1 shall be 15 inches (380 mm) long minimum. Transfer supports shall be positioned along 13 ½ inches...
Search Results "Seat Width"
Commonly Searched Documents
-
M305.2.2.1 End Transfer Supports
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
M305.2.1.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be capable of supporting transfer on each side of the transfer surface.
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side.
-
Requirement 6 -- Reinforced Walls for Grab Bars
[See subsections ...]
- Figure 802.1.2 Width of Wheelchair Spaces – Drawing from the U.S. Access Board
-
1.18 Wheelchair space, wheelchair location, or wheelchair seating
1.18Â Â Â "Wheelchair space," "wheelchair location," or "wheelchair seating" shall mean and refer to a designated space in an auditorium where a person who uses a wheelchair or motorized scooter...
- Boost Your Business - Chapter 3 - Path of Travel
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8...
-
5.1.3 Transfer Surface Low Height Options for M301 and M302
5.1.3 Transfer Surface Low Height Options for M301 and M302 The Committee did not agree on a final low height recommendation. Rationale for final recommendation (more detail...
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302 Description: Gripping surface hazards are sharp or abrasive elements that prevent an individual...
-
5.1.3 Transfer Surface Low Height
5.1.3 Transfer Surface Low Height. No agreement on final low height
-
5.1.2 Transfer Surface High Height
5.1.2 Transfer Surface High Height. The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches.
-
5.1.1 Transfer Surface Height Adjustability
5.1.1 Transfer Surface Height Adjustability. The transfer surface should have an adjustable height in small virtually continuous increments.
-
Appendix to May 23, 2014 Document
Exceptions to the 2010 Standards This table is provided for HUD recipients that elect to use the 2010 Standards under title II of the Americans with Disabilities Act (ADA) as an...
- Access Board: Sales and Service Counters
- KirbyBuilt Providence Picnic Table with Maximum Seating
-
Can an operator require a person to transfer from a wheelchair to a vehicle seat?
Section 37.165(e) of the DOT ADA regulations allows persons who use wheelchairs to transfer to a vehicle seat, if one is available....
-
Can an operator require a person to transfer from a wheelchair to a vehicle seat?
Section 37.165(e) of the DOT ADA regulations allows persons who use wheelchairs to transfer to a vehicle seat, if one is available....
-
MEASUREMENT TECHNIQUE
MEASUREMENT TECHNIQUE The depth and width are measured along the centerlines of the seat, and the height from the floor to the highest point of the transfer surface: The depth...
- NYC Board of Elections: Video 5 - Verifying Voting Equipment Setup
-
3.13(b) Dispersed Wheelchair Locations in Auditoria with More Than 300 Seats
Dispersed Wheelchair Locations in Auditoria with More Than 300 Seats In all auditoria with more than 300 seats, wheelchair spaces shall be provided in more than one location....
-
5.1 Transfer Surface Height
5.1 Transfer Surface Height