summarizes wheelbase measurements on wheeled mobility devices shown in the table below.4 Table 5.8.1.1 Wheelbase Measurements on Wheeled Mobility Devices Table !...
Search Results "Mobility Aid Seating Location"
Commonly Searched Documents
-
5.8.1.1 Clear Platform Size Recommendation
- Figure 608.5.3 Alternate Roll-In Type Shower Compartment Control Location – Drawing from the U.S. Access Board
-
Wall furr-out to support a grab bar when toilet is too far from the side wall
Here's a good example of one solution for a water closet that's too far from the adjacent side wall. Sometimes this solution is easier than moving the fixture when an offset flange...
-
Web Accessibility 101: On-Screen Keyboard Demo
Requires the Registered User plan or above. Login!
-
F206.2.4 Spaces and Elements
In assembly areas with fixed seating required to comply with F221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an accessible...
-
206.2.4 Spaces and Elements
In assembly areas with fixed seating required to comply with 221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an accessible...
-
Are accessible spaces required on all levels of a multi-level parking structure?
It depends. If a parking facility has entrances and exits on one level only, standard and van accessible spaces are required on that level so that they are on the shortest accessible...
-
1. Width and Depth of Wheelchair Spaces
The Committee stated that this size “accommodates both manual and power wheeled mobility devices including small and mid-size scooters.”...
-
2. The ADA Title III Regulation
As stated above, a public accommodation is relieved of its obligation to provide a particular auxiliary aid (but not all auxiliary aids), if to do so would result in an undue burden or a...
- Video Caption Corporation Closed Captioning and Subtitling Services
-
M303.4 Components
Where components of diagnostic equipment are used to examine specific body parts, the components shall be capable of examining the body parts of a patient seated in a wheelchair....
-
M303.4 Components
Where components of diagnostic equipment are used to examine specific body parts, the components shall be capable of examining the body parts of a patient seated in a wheelchair....
-
M302.2.3 Size
Transfer surfaces shall be 21 inches (610 mm) wide minimum and 17 inches (430 mm) deep minimum. The size of transfer surfaces shall be measured from center points of their opposing...
-
M302.3.2 Leg Supports
Where stirrups are provided, leg supports shall also be provided and comply with M305.4.
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3.
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2.
-
M302.3.1 Transfer Supports
Transfer supports shall be provided for use with transfer sides required by M302.2.4 and shall comply with M305.2.1.1, M305.2.2.1, and M305.2.3 through M305.2.8.
-
M302.2 Transfer Surface (Section-by-Section Analysis)
This is an introductory section.
-
M302.3 Supports (Section-by-Section Analysis)
This is an introductory section. An editorial change was made to this section as a result of the change in M302.3.2, described below, to replace the word “stirrups” with the term...
-
Accessible Amusement Rides - A Summary of Accessibility Guidelines for Recreation Facilities
United States Access Board Accessible Amusement Rides: A Summary of Accessibility Guidelines for Recreation Facilities This information has been developed and reviewed in...
-
Safety Always Considered
Safety Always Considered You should keep in mind that carriers are obligated to take the safety of all passengers into consideration when making decisions about accommodations for...
-
Sec.36.308(a)(1)(ii)(D)
(D) Permit individuals who use wheelchairs to sit with family members or other companions.
-
M302.3.1 Transfer Supports
Transfer supports shall be provided for use with the transfer sides required by M302.2.3 and shall comply with M305.2.
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2.
