around the water closet shall be permitted to overlap the water closet, associated grab bars, dispensers, sanitary napkin disposal units, coat hooks, shelves, accessible routes, clear floor...
Search Results "Floor Surface"
-
604.3.2 Overlap
-
(2) Adjustability: Minimum Low Transfer Height
In addressing what the low transfer height should be, 12 commenters responded to question 14 specifically addressing the proposed minimum low transfer surface height....
-
5.2.1.2 Transfer Surface Depth
5.2.1.2 Transfer Surface Depth....
-
11B-505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (864 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
11B-505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (864 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Keep wall surfaces above handrails free of any protrusions....
-
Controls [§404.3.5]
Clear floor space at controls must be located outside the door swing to prevent users from getting hit by the door....
-
Populas Vox Perfect Corner Workstation
The Vox Perfect Corner boasts a surface area of 6ft x 6ft, provides extra-low and extra-high range of adjustment, sleek design and amazing durability....
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
11B-505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (864 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
1018.7 Slopes
The slopes of beach access routes shall comply with 1018.7.
-
Running Slope [1017.7.1]
Running slope, also referred to as grade, is the lengthwise slope of a trail, parallel to the direction of travel. Trails or trail segments of any length may be constructed with...
-
Recommendation of a 19" Lower Adjsutable Height as the Minimum Accessibility Standrds (Joint Report)
Recommendation of a 19" Lower Adjsutable Height as the Minimum Accessibility Standrds (Joint Report)
-
1018.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1018.7.1) and cross slope (1018.7.2) of beach access routes.
-
7.4.3.1 Running Slope (Grade)
The running slope (grade) of trail segments shall comply with this section and shall be consistent over the distances cited. Trail running slope (grade) of up to 1:20 (5...
-
Changes in Level [4.5.2]
Vertical changes in level up to ¼ inch are permitted without treatment along accessible routes. Changes in level ¼ to ½ inch must be beveled with a slope no greater than 1:2. Changes...
-
3.1.3.3 Cross Slope of Driveways
The cross slope of driveways shall not exceed 1:33 (3 percent). Exception. The cross slope of driveways may be no more than 1:20 (5 percent) where needed to ensure proper...
-
6.7 Slope
The slopes of beach access routes shall comply with 6.7.1 and 6.7.2
-
1018.7 Slopes
The slopes of beach access routes shall comply with 1018.7.
-
1.2.5 Ramps
1.2.5 Ramps. When overall running slope and cross slope for accessible ramps are measured according to Sections 1.1.11 a recommended tolerance for these slopes is +0.5%. In the...
-
5.3.3 Transfer Sides Recommendations for M302
transfer onto the short side and the long side of the surface....
-
M304.2.2 Standing Supports (Section-by-Section Analysis)
The MDE NPRM proposed requiring standing supports on each side of the standing surface of diagnostic equipment used by patients in the standing position, and compliance with the technical...
