Section 608.5.2 covers the current ADA Standards for controls in standard roll-in type shower compartments.
Search Results "Maximum Extent Practicable"
Filters
Commonly Searched Documents
-
Standard Roll-In Type Shower Compartments: ADA Standard Section 608.5.2
-
Grab Bars: ADA Standard Section 1009.4.5
The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls....
-
11B-812.7.2 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center....
-
11B-303.3 Beveled
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (12.7 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 11B-303.3 Beveled....
-
11B-809.10.5.1 Clear floor space
The area under a lavatory, located at the control end of the tub, shall be permitted to encroach on the clear floor space provided the lavatory is 19 inches (483 mm) maximum in depth, and...
-
907.4.2.2 Height
The maximum effort to activate controls shall be no greater than 5 pounds-force. ◼...
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
Handrails
Handrails Pool stairs must have handrails with a minimum width between the rails of 20 inches and a maximum of 24 inches....
-
610.2 Bathtub Seats
The top of bathtub seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor....
-
Accessible Routes Adjacent to the Playing Surface
The accessible route provisions in ADAAG address slope (maximum of 1:12 or 8.33%), width (minimum of 36 inches), cross slope (maximum of 1:50 or 2%), handrails, and changes in level....
-
609.4 Position of Grab Bars
Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
Allowances for Typical Roadway Geometry
Allowances for Typical Roadway Geometry The 1991 ADAAG and 2004 ADA and ABA Accessibility Guidelines specify a maximum running slope of 5 percent and maximum cross slope of 2 percent...
-
Opening Force [§404.2.9]
Opening Force [§404.2.9] The maximum 5 lbf opening force applies to all accessible doors and gates except: fire doors (minimum opening force allowed by code) exterior...
-
T103 Definitions
To the extent transit agencies are concerned that deletion of this definition in the Access Board’s transportation vehicle guidelines will mean they can no longer determine what size wheelchairs...
-
Council of Citizens with Low Vision International (CCLVI)
To promote research to prevent blindness, improve maximum utilization of sight, and improve environmental conditions and access for low vision people....
-
PART 3: ACCESSIBLE EXAMINATION ROOMS
The number of examination rooms with accessible equipment needed by the medical care provider depends on the size of the practice, the patient population, and other factors....
-
Secondary market ticket sales. (Section-by-Section Analysis)
The Department is aware that the proposed rule may represent a significant change in practice for many public entities with respect to "secondary market" ticket sales. ...
-
Website Accessibility Coordinator
of this Agreement; A contact person for Content Providers on accessibility issues relating to www.edx.org, its mobile applications, the Platform, and the Accessibility Best Practices...
-
11B-409.4.3 Platform to hoistway clearance
The clearance between the car platform and the edge of any landing sill shall be 1½ inch (38 mm) maximum....
-
703.2.6 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 15 percent maximum of the height of the character....
-
11B-410.4 Platform to runway clearance
The clearance between the platform sill and the edge of any runway landing shall be 1¼ inch (32 mm) maximum....
-
1008.2.5.2 Elevated
The rise for any ramp run connecting elevated play components shall be 12 inches (305 mm) maximum....
-
410.4 Platform to Runway Clearance
The clearance between the platform sill and the edge of any runway landing shall be 1 inch (32 mm) maximum....
