Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
Search Results "Adjustable Height Counter"
-
11B-804.2 Clearance
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
Dining Surface and Work Surface
Some commenters considered the term too limiting and questioned whether it would apply, as they felt it should, to surfaces used forpurposes not necessarily considered "work," such as counters...
-
Clear Floor or Ground Space
Clear Floor or Ground Space At least one clear floor or ground space (30 inches by 48 inches minimum) must be provided at each location that has a railing height of 34 inches maximum....
-
Transfer Steps
Transfer Steps The maximum height of transfer steps is 8 inches, although shorter heights are recommended....
-
Carpet [§302.2]
The standards specify the maximum pile height (1/2” measured to the backing, cushion, or pad) and texture (level or textured loop, level cut pile, or level cut/uncut pile) and require firm...
-
Treads and Risers [4.9.2], Nosings [4.9.3]
Variation in riser height along a set of stairs can be a tripping hazard....
-
Urinal Flush Controls
The proposed rule specified a maximum height of 44 inches (the maximum height for obstructed forward reaches)....
- Equalizer 1000 Series Exercise Machine
-
Public Postsecondary Schools
and need for the academic adjustment....
-
Entry Points and Seats
When play components are located on an accessible route, the height required to transfer directly to the entry point or seat of a play component has a minimum of 11 inches (280 mm) and a...
-
704.11.1 Parapet construction
The height of the parapet shall not be less than 30 inches (762 mm) above the point where the roof surface and the wall intersect....
-
1132A.4.1 Thresholds
Changes in height at interior door thresholds (e.g., floor material changes at door thresholds) shall not exceed ½ inch (12.7 mm)....
- Sennheiser GZR 2020 Trolley for TourGuide Receivers and Transmitters Charging Case
-
T304 Operable Parts
The technical requirements for operable parts include provisions on height, location, and operation....
- FBD Partnership Three Flavors Frozen Beverage Dispenser
- FBD Partnership Two Flavors Frozen Beverage Dispenser
- Hoyer Manual Hydraulic Lift
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
ADA: Know Your Rights - Returning Service Members with Disabilities
traumatic brain injury or spinal cord injury, sustained hearing or vision loss, or are experiencing post traumatic stress disorder (PTSD) -- and now you're back in the States trying to adjust...
-
Pushbutton locator tone
The 2003 MUTCD requires that locator tone volume be carefully adjusted to be audible a minimum of 1.8 m (6 feet) and a maximum of 3.7 m (12 feet) from the pushbutton, or to the building...
-
407.4 Key Repeat (Section-by-Section Analysis)
Section-by-Section Analysis) This section proposes to require that, where a keyboard with a key repeat feature is provided, the delay before activation of the key repeat feature must be fixed at, or adjustable...
-
M306.1 General
Patients should not be required to adjust position to receive audible, visible, or tactile communications....