The Board sought comment on whether the maximum 5 pounds of force was appropriate for operating controls activated by a single finger, such as elevator call and control panel buttons, platform...
Search Results "Vertical Platform Lift"
Commonly Searched Documents
-
Maximum Force
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
Beveled: ADA Standard Section 303.3
Section 303.3 covers the current ADA Standards for beveled level changes.
-
General: ADA Standard Section 306.1
Section 306.1 of the ADA Standards covers information in the current ADA Standards for knee and toe clearance.
-
Visible Signals: ADA Standard Section 407.2.2.2
Section 407.2.2.2 covers the current ADA Standards for elevator visible signals.
-
Transfer Steps: ADA Standard Section 1009.5.4
Where possible, the height of the transfer step should be minimized to decrease the distance an individual is required to lift up or move down to reach the next step to gain access....
-
Knee & Toe Space [M303.2.4]
During a mammography procedure, the patient’s chest is flush with the front edge of the breast platform and the technician positions the patient’s breast on the breast platform....
-
§ 38.81(b)
(b) Other stepwells, and doorways with lifts, ramps or bridge plates, shall have, at all times, at least 2 foot-candles of illumination measured on the step tread or lift or ramp, when deployed...
-
11B-604.4 Seats
Seats shall not be sprung to return to a lifted position. Seats shall be 2 inches (51 mm) high maximum. [2010 ADA Standards] 604.4 Seats....
- Salsbury Industries See Through Metal Locker Double Tier 3 Wide
- Salsbury Industries See Through Metal Locker Double Tier 1 Wide
- Salsbury Industries See Through Metal Locker Triple Tier 3 Wide
- Salsbury Industries See Through Metal Locker Triple Tier 1 Wide
-
5.3.4 Grab Bars
In such cases, the riser shall have vertical or nearly vertical sides and a flat area on each side of the seat that is about 3 inches (75 millimeters) wide....
-
5.3.4 Grab Bars
In such cases, the riser shall have vertical or nearly vertical sides and a flat area on each side of the seat that is about 3 inches (75 millimeters) wide. ...
-
Section 37.71 Purchase or Lease of New Non-Rail Vehicles by Public Entities Operating Fixed Route Systems
When the lifts become available those buses would have to be retrofitted with the lifts....
-
§ 37.203(c)
(c) Except as provided in paragraph (d) of this section, when a lift is discovered to be inoperative, the entity shall take the vehicle out of service before the beginning of the vehicle's...
-
§ 37.42(c)(4)
(4) Mini-high platforms, with multiple mini-high platforms or multiple train stops, as needed, to permit access to all accessible cars available at that station; or...
-
Is a transportation operator required to carry these “overweight” wheelchairs?
Some wheelchairs weigh more than 600 pounds when occupied, and the design load of the lifts on our vehicles is 800 pounds....
-
3. Maintenance of Accessible Features
If the lift is out of order, repairs must be made in a timely fashion....
-
§ 37.163(d)
(d) Except as provided in paragraph (e) of this section, when a lift is discovered to be inoperative, the entity shall take the vehicle out of service before the beginning of the vehicle's...
-
§ 38.31(b)
(b) Other stepwells and doorways, including doorways in which lifts or ramps are installed, shall have, at all times, at least 2 foot-candles of illumination measured on the step tread,...
-
11B-411.2.1.3.4 Position
The face of individual elements or group of individual elements that are operated by user input shall slope away from the user at 15 to 25 degrees from the vertical plane. ...