The diameter or width of the gripping surface of interior handrails and stanchions shall be 11/4 inches to 11/2 inches or shall provide an equivalent gripping surface....
Search Results "Kitchen Work Surface"
Filters
Commonly Searched Documents
-
§ 38.115(a)
-
M302.2.5 Unobstructed Transfer (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they...
-
ADA Compliant Plumbing Products for Accessible Kitchens and Baths - CEU Course
Corporate Office: 317-848-1812 Course: ADA Compliant Plumbing Products for Accessible Kitchens and Baths Click here for more information or to begin course Presented By...
-
205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4....
-
Pilot Rock N-20 Series Charcoal Grill
N Series grill cooking grates are fabricated using 5/8" dia. steel bars for support handles, and 1/2" dia. steel bars for the cooking surface. ...
-
§ 38.23(b)(13) Handrails
The handrail shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less...
-
Q1: Pavement Treatment Considered an Alteration and Curb Ramp Compliance
Q1: When a pavement treatment is considered an alteration under the ADA and there is a curb ramp at the juncture of the altered road and an existing sidewalk (or other prepared surface for...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Interior Routes
INTERIOR ROUTES Floor and ground surfaces stable, firm and slip resistant. 11B-302.1 Carpet pile height 1/2 inch...
-
Balco FMS-A and FMS-V Roll-Up Floor Mat
Dirt and moisture collect underneath the grate surface to keep floors clean and reduce maintenance. Rails can be replaced without dismantling the entire grid system....
-
Nystrom Building Products MatDesign Roll-Up Mats
MatDesign™ Roll-Up Mats Aluminum rail mats with ball and socket aluminum hinges with drain holes to allow debris and moisture to flow through the mat Hinges maintain their...
-
Mats Inc. Grate Mat
Features Grate Mat "rolls up" for easy handling and maintenance. Polypropylene brush insert offers highest performance and durability. Insert options include carpet, vinyl, brush,...
-
Voting Areas
Floor surfaces must be stable, firm, and slip resistant....
-
11B-205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309....
-
11B-205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309....
-
2004 ADA and ABA Accessibility Guidelines
The following technical criteria in the proposed standards are based on the 2004 ADA and ABA Accessibility Guidelines: • Height of transfer surfaces on diagnostic equipment used by patients...
-
19 Inch Low Height
transfer surface....
-
M305.3.1.1 Horizontal Position
The length of gripping surfaces on horizontal standing supports shall be 4 inches (100 mm) minimum except for diagnostic equipment containing a wheelchair space which shall comply with M305.3.1.2...
-
Guidelines for Requirement 7
The Guidelines for Requirement 7 present design specifications for providing usable kitchens and bathrooms such that an individual in a wheelchair can maneuver about the space, as required...
-
M301.2.1 Adjustability (Section-by-Section Analysis)
The MDE NPRM proposed a transfer surface height range for diagnostic equipment used by patients in the supine, prone, or side-lying position of 17 inches minimum and 19 inches maximum....
-
M305.3.2.2 Vertical Position
The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface....
-
§ 38.23(c)(8) Handrails
them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
1014.3 Floor
The floor within camp shelters shall comply with 1014.3.
-
R304.5.3 Cross Slope
R304.5.3 Cross Slope. The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum. At pedestrian street crossings without yield or stop control...
