Floor surfaces in elevator cars shall comply with 302 and 303....
Search Results "Sign Clear Floor Space"
-
408.4.2 Floor Surfaces
-
180 Turns Around Obstructions
The clear width must be at least 48” at the turn and 42” minimum approaching the turn (unless the clear width at the turn is 60” minimum)....
-
R309.2 Parallel Parking Spaces
R309.2 Parallel Parking Spaces. Parallel parking spaces shall comply with R309.2. Advisory R309.2 Parallel Parking Spaces....
-
11B-503.2 Vehicle pull-up space
Passenger drop-off and loading zones shall provide a vehicular pull-up space 96 inches (2438 mm) wide minimum and 20 feet (6096 mm) long minimum....
-
11B-503.2 Vehicle pull-up space
Passenger drop-off and loading zones shall provide a vehicular pull-up space 96 inches (2438 mm) wide minimum and 20 feet (6096 mm) long minimum....
-
802.1 Wheelchair Spaces
802.1 Wheelchair Spaces. Wheelchair spaces shall comply with 802.1....
-
11B-809.7.1 Width
The clear width for the accessible route shall be 36 inches (914 mm) minimum. Exception: The clear width shall be permitted to be reduced to 32 inches (813 mm) minimum at doors....
-
11B-809.7.1 Width
The clear width for the accessible route shall be 36 inches (914 mm) minimum. Exception: The clear width shall be permitted to be reduced to 32 inches (813 mm) minimum at doors....
-
502.3 Access Aisle
Access aisles serving parking spaces shall comply with 502.3. Access aisles shall adjoin an accessible route. Two parking spaces shall be permitted to share a common access aisle....
-
Accessibility
Accessibility: When ceramic tile is used as the flooring surface, design professionals should consider the following, based on ANSI A108.01 and A108.02, where accessibility is a primary...
-
Side Entry: ADA Standard Section 1002.4.4.2
The amount of clear space needed within the ride, and the size and position of the opening are interrelated....
-
R410.10 Line Spacing
R410.10 Line Spacing. Spacing between the baselines of separate lines of characters within a message shall be 135 percent minimum and 170 percent maximum of the character height....
-
Extended Floor or Ground Surface: ADA Standard Section 405.9.1
Section 405.9.1 covers the current ADA Standards for extended floor or ground surface of the ramp run or landing.
-
4.3.5.3 180-degree turn around an obstacle
In effect, this condition is a space bounded by three sides and requires a lot more space because WhMD users cannot cut the corner like they can with a wider aisle width (Figure 4‒6)....
-
11B-233.3.1.2.6.5 Additional requirements.
1. Grab bar reinforcement complying with Sections 11B-809.10.5.2, 11B-809.10.6.4, or 11B-809.10.7.3. 2. Interior door opening width complying with Section 11B-404.3.1. 3....
-
R302.3 Continuous Width
Clear width requirements are contained in R304.5.1 for curb ramps and blended transitions, and in R407.4 for ramps....
-
7(2)(b)(iv)
(iv) Toilets are located within bathrooms in a manner that permit a grab bar to be installed on one side of the fixture. In locations where toilets are adjacent to walls or bathtubs,...
-
University of Louisville, Injury Risk Assessment and Prevention (iRAP) Laboratory
The Injury Risk Assessment and Prevention (iRAP) Laboratory is a multi-disciplinary laboratory that conducts state-of-the-art research through the application of engineering and...
-
Access Board: Alternate Type Roll In Shower Stalls
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
R203 Machinery Spaces (Section-by-Section Analysis)
R203 Machinery Spaces (Section-by-Section Analysis) Vaults, tunnels, and other spaces used by service personnel only are not required to comply with the proposed guidelines....
-
Crystal Sauna
control 7 Color therapy lights with a remote control Dual control panel - lowered down to 48" Thick tempered glass door and windows Large wheelchair turning space...
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
11B-807.2.1 Turning space
Turning space complying with Section 11B-304 shall be provided within the cell....
-
11B-807.2.1 Turning space
Turning space complying with Section 11B-304 shall be provided within the cell....
