Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4....
Search Results "Kitchen Work Surface"
Filters
Commonly Searched Documents
-
F205.1 General
-
205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4....
-
Boost Your Business - Chapter 3 - Path of Travel
Boost Your Business - Chapter 3 - Path of Travel
-
10.4.1(5)
Gates which must be pushed open by wheelchair or mobility aid users shall have a smooth continuous surface extending from 2 inches above the floor to 27 inches above the floor....
-
5.3.3.1 Transfer Sides Recommendation for Exam Chairs with Fixed Footrests
The Committee recommends exam chairs with a fixed footrest have a transfer surface minimum of a 17 inch depth and a 21 inch width located on both sides of the chair to allow for a left or...
-
M301.2.1 Height
The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured from the floor to the top of the transfer surface....
-
205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309. 4....
-
ADA Compliant Plumbing Products for Accessible Kitchens and Baths - CEU Course
Corporate Office: 317-848-1812 Course: ADA Compliant Plumbing Products for Accessible Kitchens and Baths Click here for more information or to begin course Presented By...
-
1.1.9 Horizontal gaps and vertical alignment
horizontal discontinuities and variations in vertical alignment such as at concrete joints, gaps, grade breaks, and at the interface of concrete with other materials or elements built into the surface...
-
Bosch Five-Point Self-Leveling Alignment Laser GPL 5 S
Description The GPL 5S is a five-point laser that levels, plumbs up, plumbs down, and squares. It accurately transfers and aligns level, plumb and 90 degree square points. With...
-
Bosch 3-Point Self-Leveling Alignment Laser GPL 3
Description Three-point plumb and level point projection laser accurately transfers and aligns plumb up/down, front level and align points; accuracy is +/- 1/4 In. at 100 ft....
-
Bosch 3 Point Self Leveling Alignment Laser Level GPL 3 S
Description The GPL3 offers limitless uses, everything from plumbing up floors and ceilings to installing drywall partitions and establishing benchmarks. And because it can be...
-
T503.5 Exterior Illumination for Boarding and Alighting Areas
Exterior lighting shall be provided to illuminate walking surfaces of boarding and alighting areas when the doors of non-rail vehicles are open....
-
Cross Slope
Cross Slope The cross slopes of gangways, transition plates and floating piers that are part of an accessible route must be designed and constructed not to exceed a maximum of 2...
-
Addendum D: Comparison of demographics and transfer height between Phase 1 and Phase 2 of the study
[See subsections ...]
-
4.3.7 Slope
An accessible route with a running slope greater than 1:20 is a ramp and shall comply with 4.8. Nowhere shall the cross slope of an accessible route exceed 1:50.
-
4.3.7 SLOPE
An accessible route with a running slope greater than 1:20 is a ramp and shall comply with 4.8. Nowhere shall the cross slope of an accessible route exceed 1:50.
-
Electronic instruments
Electronic instruments have been developed to measure floor flatness. Originally created to measure the flatness of concrete floors in critical applications such as narrow - aisle...
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance
-
Braille Works
Let Braille Works handle your 508 document repair and remediation....
-
5.4.2.2 Transfer and Positioning Support Length for Imaging Equipment with Transfer Surfaces
5.4.2.2 Transfer and Positioning Support Length for Imaging Equipment with Transfer Surfaces....
-
Wheeled Mobility Anthropometry Project
The data and recommendations from the Wheeled Mobility Anthropometry Project are discussed in connection with the following technical criteria: • Height of transfer surfaces on diagnostic...
-
Gripping Surface Cross Section and Clearances M301, M302, and M305.2
Gripping Surface Cross Section and Clearances M301, M302, and M305.2 Gripping surface for transfer supports shall be free of sharp or abrasive elements and shall have rounded edges per...
-
M302.2.5 Unobstructed Transfer
Each transfer side complying with M302.2.4 shall provide unobstructed access to transfer surfaces. EXCEPTIONS: 1....
