Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2....
Search Results "Expected Maximum Flight Duration"
-
M303.3.2 Beveled
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-903.5 Height
The top of the bench seat surface shall be 17 inches (432 mm) minimum and 19 inches (483 mm) maximum above the finish floor or ground....
-
11B-703.2.8 Line spacing
Spacing between the baselines of separate lines of raised characters within a message shall be 135 percent minimum and 170 percent maximum of the raised character height....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
Specifically, the Access Board indicated it was considering requiring circular cross sections to have an outside diameter of 1¼ inches minimum and 2 inches maximum, and transfer supports...
-
Regional Access & Mobilization Project (RAMP) - Rockford, Belvidere, DeKalb, Freeport, IL
is a non-profit, non-residential Center for Independent Living (CIL) that emulates the Independent Living Philosophy with a mission that promotes an accessible society that allows and expects...
-
Transfer Protocols
The maximum and minimum transfer heights that were attainable were recorded....
-
Fur out the wall
The centerline of the water closet shall be 16 inches (405 mm) minimum to 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430...
-
Williams Sound PPA 458 NET PERSONAL PA® FM ASSISTIVE LISTENING SYSTEM
Features three powerful microprocessors and the same high-quality audio and RF performance you’ve come to expect from Williams Sound....
-
Stanley QRM 100 Series Grade 1 Extra Heavy Duty Exit Devices
All Stanley exit devices are manufactured to heavy duty, architectural grade expectations and meet or exceed ANSI Grade 1 specifications....
-
Activar Hiawatha 5-1/2P Series Pull with Matching Push Plate
Since 1954, Hiawatha has been providing consistent customer service with the high-quality materials and finishes that you have come to expect. ...
-
Williams Sound PPA 457 PERSONAL PA® FM ASSISTIVE LISTENING SYSTEM
Features three powerful microprocessors and the same high-quality audio and RF performance you’ve come to expect from Williams Sound....
-
Reasonable Accommodation Management Software
All the things you’d expect in a comprehensive RA system are here including on-demand training for line supervisors and human resource professionals. ...
-
Williams Sound PPA 458 PERSONAL PA® FM ASSISTIVE LISTENING SYSTEM
Features three powerful microprocessors and the same high-quality audio and RF performance you’ve come to expect from Williams Sound....
-
Williams Sound PPA 457 NET PERSONAL PA® FM ASSISTIVE LISTENING SYSTEM
Features three powerful microprocessors and the same high-quality audio and RF performance you’ve come to expect from Williams Sound....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
§382.133(f)(3)
(3) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with the safety regulations...
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....
-
902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....
-
703.5.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter "O" is 55 percent minimum and 110 percent maximum of the height of the uppercase letter "I"....
-
703.2.4 Character Proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 55 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
