The investigation and compliance review conducted by the Department found that the Museum initially failed to implement means to ensure that people with disabilities have an equal opportunity...
Search Results "Compliance Date"
Filters
Commonly Searched Documents
-
C. FINDINGS BY THE UNITED STATES
-
I. Adoption of Final Guidelines
The Department believes that the final Guidelines adopted by this notice (1) are consistent with the level of accessibility envisioned by Congress; (2) simplify compliance with the Fair...
-
Accessibility of Airport Facilities
[Sec. 382.55(c)] 1 Compliance with the requirements applying to places of public accommodation under Department of Justice (DOJ) regulations implementing Title III of the Americans...
-
The Purpose of FSORAG and FSTAG
Compliance with FSORAG and FSTAG does not mean that all recreation areas and trails will be accessible to all persons with disabilities; in some locations, the natural environment will prevent...
-
Step 1: Determine the Applicability of FSTAG
Even if compliance with FSTAG is not required, you should try to incorporate accessibility where opportunities exist and to the extent you can without changing the character of the setting...
-
III-4.4300 Standards to apply
Deviations from ADAAG are acceptable only when full compliance with those requirements is not readily achievable....
-
Can I Get Additional ADA Information and Assistance?
The EEOC conducts an active technical assistance program to promote voluntary compliance with the ADA....
-
Section 37.21 Applicability—General
For entities which do receive Federal funds, compliance with the ADA and part 37 is a condition of compliance with section 504 and 49 CFR part 27, DOT's section 504 rule....
-
II-8.1000 General
Title II requires that public entities take several steps designed to achieve compliance. These include the preparation of a self-evaluation....
-
Sargent 6500 Line Lever Hardware with Lockset
Cylinder: Brass, 6 pin, LA keyway standard Finishes : 3, 4, 10, 10B, 26, 26D (No Split Finish) Door Prep: ANSI A115.2 (161) Modified Minimum Stile: 4-1/2" (114mm) Certification Compliance...
-
1009.2.1 Pool Lift Location
Where the entire pool depth is greater than 48 inches (1220 mm), compliance with 1009.2.1 shall not be required. 2....
-
Sec.36.304(d)(2)
(2) If, as a result of compliance with the alterations requirements specified in paragraph (d)(1) of this section, the measures required to remove a barrier would not be readily achievable...
-
1. Adoption of the 2010 ADA Standards for Accessible Design
To minimize compliance burdens on entities subject to more than one legal standard, these design standards have been harmonized with the Federal standards implementing the Architectural...
-
1. Adoption of the 2010 ADA Standards for Accessible Design
To minimize compliance burdens on entities subject to more than one legal standard, these design standards have been harmonized with the Federal standards implementing the Architectural...
-
403.5.2 Clear Width at Turn
EXCEPTION: Where the clear width at the turn is 60 inches (1525 mm) minimum compliance with 403.5.2 shall not be required. Figure 403.5.2 Clear Width at Turn...
-
Exceptions [1014.1, Exceptions 1 and 2]
When a condition for exception does not permit full compliance with a specific provision in the technical requirements for camp shelters, the camp shelter must comply with the specific provision...
-
12185(e) Review
the study required by subsection (a) of this section, the Office of Technology Assessment shall provide a preliminary draft of such study to the Architectural and Transportation Barriers Compliance...
-
412.1 General (Section-by-Section Analysis)
Would compliance with section 412 be readily achievable for manufacturers of mobile telecommunications equipment?...
-
106.5.68 Technically Infeasible
essential part of the structural frame; or because other existing physical or site constraints prohibit modification or addition of elements, spaces, or features that are in full and strict compliance...
-
4.1.7(1)(a) General Rule
applicable technical specifications of 4.2 through 4.35 and the applicable special application sections 5 through 10 unless it is determined in accordance with the procedures in 4.1.7(2) that compliance...
-
10.2.1(3)
Signs that are sized to the maximum dimensions permitted under legitimate local, state or federal regulations or ordinances shall be considered in compliance with 4.30.2 and 4.30.3 for purposes...
-
4.1.7(2)(a)(ii) ADA Application
If the State Historic Preservation Officer or Advisory Council on Historic Preservation agrees that compliance with the requirements for accessible routes (exterior and interior), ramps,...
-
LARGE AREA ASSISTIVE LISTENING SYSTEMS (ALS): REVIEW AND RECOMMENDATIONS
Large Area Assistive Listening Systems: Review and Recommendations Final Report to United States Architectural and Transportation Barriers Compliance Board (U.S....
-
3.4.1 General
When a new viewing area is constructed, or an existing viewing area is altered or reconstructed, if a condition for exception in section 1.1 prohibits full compliance with a specific requirement...
