Exceptions: Transfer systems complying with Section 11B-1008.3 shall be permitted to connect elevated play components except where 20 or more elevated play components are provided...
Search Results "Side Transfer Surface"
-
11B-1008.2.1 Ground level and elevated play components
-
1008.2.1 Ground Level and Elevated Play Components
Transfer systems complying with 1008.3 shall be permitted to connect elevated play components except where 20 or more elevated play components are provided no more than 25 percent of the...
-
1008.2.6.2 Use Zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
1017.8.3 Slope
Where the surface is other than asphalt, concrete, or boards, slopes not steeper than 1:20 are permitted when necessary for drainage....
-
11B-1008.2.1 Ground level and elevated play components
Transfer systems complying with section 11B-1008.3 shall be permitted to connect elevated play components except where 20 or more elevated play components are provided no more than 25 percent...
-
11B-1008.2.1 Ground level and elevated play components
Transfer systems complying with section 11B-1008.3 shall be permitted to connect elevated play components except where 20 or more elevated play components are provided no more than 25 percent...
-
1008.2.1 Ground Level and Elevated Play Components
Transfer systems complying with 1008.3 shall be permitted to connect elevated play components except where 20 or more elevated play components are provided no more than 25 percent of the...
-
Handrails Along Walkways
Handrails Along Walkways. The 1991 Standards do not contain any technical requirement for handrails provided along walkways that are not ramps. Section 403.6 of the 2010 Standards...
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
Slope Ratio
Slope Ratio—A ratio of vertical distance to horizontal distance or rise to run.
-
Trail Construction Techniques
Information that is already available to Forest Service employees is not repeated in this guidebook. The "Trail Construction and Maintenance Notebook" includes practical techniques...
-
2. Methodology
[See subsections ...]
-
1017.7 Slopes
The slopes of trails shall comply with 1017.7.
-
1.1.6 Flatness of walk cross slope
measurement is based on the assumption that most accessible exterior walks will be at least 60 in. (1525 mm) wide due to passing requirements and that users will tend to stay toward one side...
-
Pilot Rock ART Series End Accessible Recycled Plastic Picnic Table With Arched Frame
Tables won’t tip even if all persons sit on one side. Tables offer 30-1/2" nom. table height and 17-1/2" nom. seat height....
-
1017.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
1017.8.3 Slope
EXCEPTION: Where the surface is other than concrete, asphalt, or boards, cross slopes not steeper than 1:20 shall be permitted when necessary for drainage....
-
Using Patient Lifts
Using Patient Lifts Medical providers may need a lift in order to transfer some patients safely onto an exam table....
-
Handrails
...are there handrails on both sides of the stair at a uniform height of 34"-38" above the front edge of the step?...
-
A5.1 General
Dining counters (where there is no service) are typically found in small carry-out restaurants, bakeries, or coffee shops and may only be a narrow eating surface attached to a wall....
-
Section C: Exterior Route
(§303) C3 Is the route free of surface openings greater than 1/2", such as grates or holes in the pavement?...
-
4.35.4 Bench
Clear floor space shall be provided alongside the bench to allow a person using a wheelchair to make a parallel transfer onto the bench....
-
1015.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
-
M304.3 Standing Supports
Standing supports shall be provided on each side of the standing surface and shall comply with M305.3....
