See Chapter 35.
Search Results "Proposed Standard"
-
11B-105.1 General
-
11B-105.1 General
See Chapter 35.
-
Federal Trail Data Standards (FTDS)
Standardized terminology that enable national, regional, and State trail managers, and the public, to use mutually understood terminology for recording, retrieving, and applying spatial...
-
12186(d)(1) Facilities
alteration authorized by such permit begins within one year of the receipt of such permit and is completed under the terms of such permit, compliance with the Uniform Federal Accessibility Standards...
-
§100.201a(c)
(c) The 1986, 1992, 1998, and 2003 editions of ANSI A117.1 may be inspected at the Department of Housing and Urban Development, 451 Seventh Street, SW., Room 5240, Washington, DC...
-
1991 ADA Standards for Accessible Design
Department of Justice 28 CFR Part 36 Nondiscrimination on the Basis of Disability by Public Accommodations and in Commercial Facilities Excerpt from 28 CFR Part 36: ADA Standards...
-
§ 38.1 Purpose
This part provides minimum guidelines and requirements for accessibility standards in part 37 of this title for transportation vehicles required to be accessible by the Americans With...
-
DOJ’s 2010 ADA Standards for Accessible Design
DOJ’s 2010 ADA Standards for Accessible Design became effective March 15, 2012 and apply to all facilities covered by the ADA except public transit facilities....
-
Background
Background While the current ADA/ABA Accessibility Guidelines (ADA/ABA Guidelines) make reference to standard industry construction tolerances as they relate to the dimensions given in...
-
G. Response to 2008 NPRM Comments Concerning Movie Captioning and Video Description, Analysis and Discussion of Proposed Regulatory Approach
Response to 2008 NPRM Comments Concerning Movie Captioning and Video Description, Analysis and Discussion of Proposed Regulatory Approach Although the 2008 NPRM did not propose any specific...
-
One Set of Design Standards
A number of commenters objected to the fact that the proposed guidelines included more than one set of design standards....
-
11B-411.2.1.2.1 Keypads
Keypads shall be in a 12-key ascending telephone keypad layout. Characters and symbols shall be centered on the corresponding button. The number five key shall have a single raised...
-
11B-411.2.1.2.1 Keypads
Keypads shall be in a 12-key ascending telephone keypad layout. Characters and symbols shall be centered on the corresponding button. The number five key shall have a single raised...
-
§1194.1 Standards for Section 508 of the Rehabilitation Act.
The standards for information and communication technology developed, procured, maintained, or used by Federal agencies covered by Section 508 of the Rehabilitation Act are set forth in...
-
1630.10 Qualification standards, tests, and other selection criteria
1630.10 Qualification standards, tests, and other selection criteria....
-
§ 35.151(c) Accessibility standards
(c) Accessibility standards....
-
12113(c) Qualification standards and tests related to uncorrected vision
(c) QUALIFICATION STANDARDS AND TESTS RELATED TO UNCORRECTED VISION.— Notwithstanding section 12102(4)(E)(ii), a covered entity shall not use qualification standards, employment tests, or...
-
Sec. 12163. Conformance of accessibility standards. [Section 243]
Accessibility standards included in regulations issued under this subpart shall be consistent with the minimum guidelines issued by the Architectural and Transportation Barriers Compliance...
-
Section 1630.10 Qualification Standards, Tests, and Other Selection Criteria
Section 1630.10 Qualification Standards, Tests, and Other Selection Criteria...
-
How to Use the ADA 2010 Standards Electronic Pocket Guide
-
Receiver Jacks: ADA Standard Section 706.2
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
11B-706.2 Receiver jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
11B-706.2 Receiver jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
Chapter 7: Referenced Standards
[See subsections ...]