Requires the Registered User plan or above.
Login!
Search Results "Parking Surface"
-
Door King Inc. Seamless Access Control with the DKS 9000 Vehicular Slide Gate Operator
-
Door King Inc. 6400 In-Ground Gate Operators Video
Requires the Registered User plan or above. Login! -
Door King Inc. Versatility of the DKS 9100 Vehicular Sliding Gate Operator
Requires the Registered User plan or above. Login! -
Door King Inc. DKS Easy Setup For Vehicular Slide Gate Operators
Requires the Registered User plan or above. Login! -
Door King Inc. 6004 Column Mount Swing Gate Operator Solar Powered
Requires the Registered User plan or above. Login! -
Door King Inc. 9000 Vehicular Sliding Gate Operator Replaces SL3000
Requires the Registered User plan or above. Login!
-
Check-Out Aisles [7.3]
Writing surfaces must be 36 inches maximum from the floor....
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
Poured in Place Rubber
The surface cost for PIP ranged from $6.59/sq. ft. to $19.80/sq. ft. ...
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
Re: DSA Drawing 11B-406-1C Curb Ramp Adjoining a Parking Access Aisle next to a Curb and Gutter (2016 CBC)
This drawing should show that the gutter is not included in the required min 18’ depth. The dashed lines don’t spell it out clearly enough to me.
-
The Brewer Company, LLC
Company, LLC Minority Report The Brewer Company, LLC 01-Oct-2013 Final Report Medical Diagnostic Equipment Accessibility Standards Advisory Committee Section 5.1.3 Transfer Surface...
-
Beneficial Designs The Universal Trail Assessment Process (UTAP)
Illustrated step-by-step instructions show how to use each assessment tool, how to accurately measure grade, cross slope , width, and obstacles and how to describe surface type....
-
How to Measure Transfer Surface Height
How to Measure Transfer Surface Height Regardless of the final decision on the low height measurement, the Subcommittee agreed that the height of the transfer surface would be measured...
-
4.3.3 Slope
When the surface is not paved or is not elevated above the natural ground, slopes not steeper than 1:33 (3 percent) shall be permitted where necessary for drainage. ...
-
Clearances Around Gripping Surfaces
Guidelines specify the following clearances around grab bars to ensure sufficient space for a person to grasp the grab bar: 1½ inches absolute clearance between grab bars and the adjacent wall surfaces...
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
(2) Transfer Surface Location for Diagnostic Equipment Used in the Seated Position
Transfer onto these types of diagnostic equipment must be made from either long side, similar to the side transfer surface described above....
-
§ 38.125(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
-
2010 ADA Standards - Plan Review Tool - Slopes
2010 ADA Standards - Plan Review Tool - Slopes Click here to view/download the pdf "2010 ADA Standards - Plan Review Tool - Slopes" (774 KB) * * * * * * *
-
1017.6 Openings
Openings in the surface of trails, passing spaces, and resting intervals shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1017.6 Openings. ...
-
1133A.4.1 Exceptions
Two 15-inch (381 mm) wide minimum breadboards may be provided in lieu of the required 30 inches (762 mm) of countertop work surface, and used without meeting the repositioning requirements...
