Thanks for the insights, Dan! It's crucial to clarify aisle width requirements, especially when it impacts accessibility. This reminds me of quordle—every word choice matters, just...
Search Results "Hinge Side Clearance"
-
Re: Caution regarding minimum Aisle Widths for aisles that serve "elements on both sides"
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
4.13.11(2)(a)
(a) exterior hinged doors: (Reserved)....
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404 except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with 404 except that if the approach is to the latch side of the compartment door, clearance between the door side of the...
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
4.13.11(2)(b)
(b) interior hinged doors: 5 lbf (22.2N)...
-
MEASUREMENT TECHNIQUE
measured along the centerlines of the seat, and the height from the floor to the highest point of the transfer surface: The depth is measured between the perineal cutout and the hinge...
-
4.13.11* DOOR OPENING FORCE
(a) exterior hinged doors: (Reserved)....
-
2.2.6 Door Use
clearance > 1525 mm > 1525 mm > 1525 mm Pull side clearance > 1525 mm > 1525 mm > 1525 mm Push side latch side...
-
1010.1.7 Thresholds
In occupancy Group R-2 or R-3, threshold heights for sliding and side-hinged exterior doors shall be permitted to be up to 7¾ inches (197 mm) in height if all of the following apply:...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
1118B.6
SECTION 1118B - SPACE ALLOWANCE AND REACH RANGES 1118B.6 Side reach. ...
-
Design Opportunity
The pictured example vanity using the stock bracket and dimensions shown in section view may not provide the required minimum 8" deep knee clearance at 27" AFF under the vanity top (306)...
-
Accessible Parking Video Fact Sheet
Troy Balthazor, ADA Specialist for the Great Plains ADA Center, gives an overview of accessible parking requirements from the 2010 ADA Standards for Accessible Design. Technical...
-
Are doors or gates to employee work areas required to comply?
Entry doors or gates to employee work areas are required to meet applicable requirements, including those for maneuvering clearance, on the exterior, but not the interior....
-
Lavatory & Accessory Layouts
The trash receptacle is preferred to be near the door to allow people to pull the door open with a paper towel and drop it into the receptacle before exiting.
-
Do access aisle borders (in blue) have to be painted on all four sides to be considered compliant?
I would say yes as the language in the code is pretty specific using the term "perimeter". I would also say that both of the "end" lines would/could be within the required length.
-
Clear Deck Space
This will allow persons using a wheelchair to turn around and access the wall, depending on the side they can best use to transfer....
-
11B-809.10.5.4 Bathtub enclosures
Hinged doors shall open outward. Glazing used in doors and panels of bathtub enclosures shall be fully tempered, laminated safety glass or approved plastic....
