Exceptions 1 – 3 are preempted by Florida vertical accessibility requirements of s.553.509, F.S., as incorporated in section 201.1.1....
Search Results "Vertical Actuation Bar"
-
206.2.4 Spaces and Elements
-
Sight Lines
Sight Lines Both the horizontal and vertical viewing angles must be considered in the design of assembly areas....
-
M301.2.1, M302.2.1 Transfer Height
These surfaces may range between 4” to 5” in thickness - this will add to the vertical height of a stretcher when measuring from the floor to the top of the surface (uncompressed)....
-
206.2.3 Multi-Story Buildings and Facilities
Exceptions 1 – 7 are preempted by Florida vertical accessibility requirements of s. 553.509, F.S., as incorporated in section 201.1.1....
-
ASME
Lifts are classified as: vertical platform lifts, inclined platform lifts, inclined stairway chairlifts, private residence vertical platform lifts, private residence inclined platform lifts...
-
Background
In these studies, subjects who stood to transfer consistently reported that the preferred ADA configuration was the most difficult to use, whereas grab bars on both sides of the toilet,...
-
ADAPTABLE
As part of the initial design and construction, for example, structural backing would be provided for the later installation of grab bars, base cabinets under kitchen sinks would be removable...
-
ADAPTABLE
As part of the initial design and construction, for example, structural backing would be provided for the later installation of grab bars, base cabinets under kitchen sinks would be removable...
-
4.2 Stretchers
First, to serve these multiple purposes, the current configuration of stretchers must accommodate the vertical height needs of numerous components, including (Figure 3.1): the basic elements...
-
Surfaces (R302.7) (Section-by-Section Analysis)
Vertical alignment of surfaces within pedestrian access routes (including curb ramp runs, blended transitions, turning spaces, and gutter areas within pedestrian access routes) and within...
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
R405.1 General
Clearances are measured in relation to the usable clear space, not necessarily to the vertical support for an element....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
7.4.5.1 Size
Vertical alignment at the intersection of the trails that form the T-shaped space shall be nominally level....
-
Parking and Passenger Loading Zones [4.6]
Accessibility also includes the appropriate designation and location of spaces and passenger loading zones, their connection to an accessible route, and vertical clearance for vans....
-
Spout Location [4.15.3]
The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
§ 38.73(d)(1) Requirements
Vertical alignment may be accomplished by vehicle air suspension, automatic ramps or lifts, or any combination....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
- Corbin Russwin Inc. ED7000 Series Narrow Stile Crossbar Exit Device
- Husky 24" Line Generator Digital Laser Level
-
Addendum F: Relative Height Differences
Adjustable Height No Grab Bars/No Backrest Maximum Height (n=71) .300 3.5 5.00 9.00 13.7...
- American Standard Acrylic Seated Safety Shower