Passenger drop-off and loading zones shall provide a vehicular pull-up space 96 inches (2438 mm) wide minimum and 20 feet (6096 mm) long minimum....
Search Results "Lavatory Clear Floor Space"
Filters
Commonly Searched Documents
-
11B-503.2 Vehicle pull-up space
-
Employee Work Areas: ADA Standard Section 203.9
Section 203.9 covers scoping requirements of general exceptions for employee work areas in the most current ADA Standards.
-
408.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
408.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
802.1 Wheelchair Spaces
802.1 Wheelchair Spaces. Wheelchair spaces shall comply with 802.1....
-
Inpro Corporation JointMaster® 787 Series Floor Expansion Joint Covers
cover plate for added slip resistance Integral, high durometer seal deters water from entering the system and acts as a noise dampening device Key Specifications Floor...
-
Whitehall Mfg. 3373-WSF Single Temp Hemispherical Widespread Pushbutton Pneumatic Valve Conical Faucet
The Ligature Resistant Faucet is arranged to be mounted to the deck of the lavatory. Faucet assembly requires two 1-1/2” diameter holes....
-
Whitehall Mfg. Single Temp Hemispherical Widespread Pushbutton Pneumatic Valve Conical Faucet
The Ligature Resistant Faucet is arranged to be mounted to the deck of the lavatory. Faucet assembly requires two 1-1/2” diameter holes....
-
Visible Indicators: ADA Standard Section 407.4.7.1.4
Section 407.4.7.1.4 covers the current ADA Standards for visible indicators on elevator car control buttons.
-
11B-407.4.7.1.4 Visible indicators
Buttons with floor designations shall be provided with visible indicators to show that a call has been registered....
-
180 Turns Around Obstructions
The clear width must be at least 48” at the turn and 42” minimum approaching the turn (unless the clear width at the turn is 60” minimum)....
-
R410.10 Line Spacing
R410.10 Line Spacing. Spacing between the baselines of separate lines of characters within a message shall be 135 percent minimum and 170 percent maximum of the character height....
-
Side Entry: ADA Standard Section 1002.4.4.2
The amount of clear space needed within the ride, and the size and position of the opening are interrelated....
-
502.3 Access Aisle
Access aisles serving parking spaces shall comply with 502.3. Access aisles shall adjoin an accessible route. Two parking spaces shall be permitted to share a common access aisle....
-
Whitehall Mfg. Single Temp Piezo Widespread Pushbutton Electronic Valve Conical Faucet
The Ligature Resistant Faucet is arranged to be mounted to the deck of the lavatory. Faucet assembly requires two 1-1/2” diameter holes....
-
11B-809.7.1 Width
The clear width for the accessible route shall be 36 inches (914 mm) minimum. Exception: The clear width shall be permitted to be reduced to 32 inches (813 mm) minimum at doors....
-
Accessibility
Accessibility: When ceramic tile is used as the flooring surface, design professionals should consider the following, based on ANSI A108.01 and A108.02, where accessibility is a primary...
-
4.3.5.3 180-degree turn around an obstacle
In effect, this condition is a space bounded by three sides and requires a lot more space because WhMD users cannot cut the corner like they can with a wider aisle width (Figure 4‒6)....
-
R203 Machinery Spaces (Section-by-Section Analysis)
R203 Machinery Spaces (Section-by-Section Analysis) Vaults, tunnels, and other spaces used by service personnel only are not required to comply with the proposed guidelines....
-
Bradley Oval Handwashing Basin SL-TO1
Material, available in dozens of colors Molded integral overflow Integrates with Terreon solid surface countertops for a seamless fixture Specify as a prefabricated LD3010 Omnideck Lavatory...
-
Extended Floor or Ground Surface: ADA Standard Section 405.9.1
Section 405.9.1 covers the current ADA Standards for extended floor or ground surface of the ramp run or landing.
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
R302.3 Continuous Width
Clear width requirements are contained in R304.5.1 for curb ramps and blended transitions, and in R407.4 for ramps....
