Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical. Figure 303.2 Vertical Change in Level...
Search Results "Expected Maximum Flight Duration"
-
303.2 Vertical
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range with specific minimum or maximum end points....
-
A2
Is the vehicle pull-up area relatively level (1:50 or 2% maximum slope in all directions)? Yes No...
-
4.18.2 Height
Urinals shall be stall-type or wall-hung with an elongated rim at a maximum of 17 in (430 mm) above the finish floor....
-
3.1 GRAPHIC CONVENTIONS
Dimensions that are not marked "minimum" or "maximum" are absolute, unless otherwise indicated in the text or captions....
-
Conventions [§104]
Conventions [§104] Most dimensions in the ADA Standards are specified as a minimum, maximum, or as a range. In a few areas, absolute dimensions are specified....
-
Ramps
Slightly steeper running slopes are permitted for short ramps (maximum 6” rise) where space is limited (§405.2, Ex.)....
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
11B-703.2.6 Stroke thickness
Stroke thickness of the uppercase letter “I” shall be 15 percent maximum of the height of the character....
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
11B-809.9.5 Lower shelving
Lower shelving and/or drawer space shall be provided at a height of 48 inches (1219 mm) maximum above the finish floor....
-
11B-809.8.2 Door opening force
The opening force for primary entry exterior doors and secondary exterior doors shall be 8.5 pounds (38 N) maximum....
-
602.4 Spout Height
Spout outlets shall be 36 inches (915 mm) maximum above the finish floor or ground....
-
What Assistance Will the Person(s) Provide?
Agreement should be reached regarding how long the person giving assistance is expected to wait for the first responders to arrive....
-
Bathroom Design Illustrations
Department believes that to indicate, through the Guidelines, that a parallel approach to the tub is necessary to meet the Act's requirements, exceeds the Fair Housing Act's minimal design expectations...
-
Allowances for Typical Roadway Geometry
Allowances for Typical Roadway Geometry The 1991 ADAAG and 2004 ADA and ABA Accessibility Guidelines specify a maximum running slope of 5 percent and maximum cross slope of 2 percent...
-
Opening Force [§404.2.9]
Opening Force [§404.2.9] The maximum 5 lbf opening force applies to all accessible doors and gates except: fire doors (minimum opening force allowed by code) exterior...
-
EQUITABLE RELIEF
The determination of appropriate auxiliary aids and services, and the timing, duration, and frequency with which they will be provided, must be made at the time an appointment is scheduled...
-
11B-232.2.1.3 Substitute cells
Integrated with the other cells to the maximum extent feasible....
-
11B-232.2.1.3 Substitute cells
Integrated with the other cells to the maximum extent feasible....
-
11B-809.10.5.1 Clear floor space
The area under a lavatory, located at the control end of the tub, shall be permitted to encroach on the clear floor space provided the lavatory is 19 inches (483 mm) maximum in depth, and...
-
11B-303.3 Beveled
Changes in level between ¼ inch (6.4 mm) high minimum and ½ inch (12.7 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 11B-303.3 Beveled....
-
11B-809.10.5.1 Clear floor space
The area under a lavatory, located at the control end of the tub, shall be permitted to encroach on the clear floor space provided the lavatory is 19 inches (483 mm) maximum in depth, and...