Where signs identify a station or its entrance, at least one sign at each entrance shall comply with Section 11B-703.2 _|Signs; Raised Characters|_ and shall be placed in uniform locations...
Search Results "Character Width (VMS)"
-
11B-810.6.1 Entrances
-
12184(c)(1) Exception
(1) Exception To the extent that compliance with subsection (a)(2)(C) or (a)(7) of this section would significantly alter the historic or antiquated character of a historical or antiquated...
-
11B-703.7 Symbols of accessibility
Symbols of accessibility, such as the International Symbol of Accessibility (ISA), which are included on signs with raised characters and Braille are not required to be raised....
-
11B-810.6.1 Entrances
Where signs identify a station or its entrance, at least one sign at each entrance shall comply with Section 11B-703.2 _|Signs; Raised Characters|_ and shall be placed in uniform locations...
-
Section 36.303(g)(1) Closed Movie Captioning
“Closed Movie Captioning” The NPRM defined “closed movie captioning” as “the written text of the movie dialogue and other sounds or sound making (e.g. sound effects, music, and the character...
-
4.3.3 Clear Floor Area
The clear floor area width also informs the minimum clearance width for successful passage through corridors, doorways and ramps....
-
11B-608.2.2 Standard roll-in type shower compartments
shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides with a full opening width...
-
11B-608.2.2 Standard roll-in type shower compartments
shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides with a full opening width...
-
2. Shoulder Breadth
Shoulder Breadth Shoulder breadth tends to be slightly greater than hip or thigh breadth and hence was used as an estimate for the width of an examination table when in a reclined position...
-
Taking Measurements
Measuring slope using a 24-inch level and tape measure Using the Tape Measure When measuring the width of a parking space or access aisle, the width of an accessible route or the height...
-
Symmetry Vertical Platform Lift VPC-EL
A cost-effective solution, platform lifts create convenient access without compromising architectural character, Designed for ease of installation, Symmetry platform lifts are equipped with...
-
i. EIT for effective communication in accessible rooms
Real-time text communications refer to those that are sent and received on a character-by-character basis; the characters are sent immediately once typed and also displayed immediately to...
-
Selecting a TTY
The number of characters in the display at one time may vary from 1 line (20 characters) to 2 lines (80 characters)....
-
5.8.1.1 Clear Platform Size
The platform should be a minimum clear width of 32-inches and a minimum clear length of 40-inches....
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
-
11B-705.1.2.5 Hazardous vehicular areas
Detectable warnings at hazardous vehicular areas shall be 36 inches (914 mm) in width....
-
11B-703.1.1.2 Inspection
The inspection shall include, but not be limited to, verification that Braille dots and cells are properly spaced and the size, proportion and type of raised characters are in compliance...
-
11B-703.1.1.2 Inspection
The inspection shall include, but not be limited to, verification that Braille dots and cells are properly spaced and the size, proportion and type of raised characters are in compliance...
-
11B-812.6 Vehicle spaces
All vehicle spaces shall be marked to define their width. Exceptions: 1....
-
11B-812.6 Vehicle spaces
All vehicle spaces shall be marked to define their width....
-
Clearance Around Base (M301.4.2 and M302.4.2)
The width of the base permitted within this clearance would be 26 inches wide maximum at the edge of the examination surface and is permitted to increase at a rate of 1 inch in width for...
-
Door Maneuvering Clearance
The final rule includes clarification, which was partially contained in a previous footnote to Table 404.2.4.1, that maneuvering clearances "shall extend the full width of the doorway and...
-
403 Walking Surfaces
Section 403.5 includes requirements for the clear width of walking surfaces....
