Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer surface...
Search Results "Walking Surface"
Filters
Commonly Searched Documents
-
M305.2.1 Location
-
1009.4.4 Surface
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges....
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and maximum...
-
M305.2.3 Height (Section-by-Section Analysis)
Board sought input from the public in question 20 of the MDE NPRM preamble, on whether a transfer support height requirement of 6 inches minimum and 19 inches maximum above the transfer surface...
-
WILLITS, et al v. CITY OF LOS ANGELES - Settlement Terms
Willits v. City of Los Angeles Term Sheet as of March 30, 2015
-
WILLITS, et al v. CITY OF LOS ANGELES - Settlement Agreement and Release of Claims
UNITED STATES DISTRICT COURT CENTRAL DISTRICT OF CALIFORNIA CASE NO. CV 10-5782 CBM (RZx) SETTLEMENT AGREEMENT AND RELEASE OF CLAIMS MARK WILLITS, JUDY GRIFFIN,...
-
11B-705.1.1.3.2
Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking surfaces....
-
M305.2.1 Location (Section-by-Section Analysis)
surface depths of greater than 24 inches....
-
5.4.5 Transfer Support Position for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer gripping surface should be located within the minimum and maximum heights....
-
d. Unobstructed Transfer
The MDE NPRM proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they could be repositioned...
-
11B-224.7 Housing at a place of education
and clustered sleeping rooms) or on floors containing accessible sleeping rooms with mobility features shall provide turning spaces that comply with Section 11B-809.2.2 and kitchen work surfaces...
-
Sloped Surfaces
Measuring the slope of a ramp, parking space, pedestrian route, or other ground or floor surface is important to identify whether the surface is accessible....
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
Transfer supports should be required on both sides of the transfer surface and be movable or removable so they can be out of the way during transfer....
-
A Wheelchair Rider's Guide to the California Coast
Explore, enjoy, protect. Rolling across the sand in a beach wheelchair Fishing from an accessible pier Hiking an accessible trail or...
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
provide options to transfer onto the short side and the long side of the surface....
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer support should be a minimum length of 15 inches positioned so that the transfer support overlaps the minimum depth of the transfer surface by 80%....
-
1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
Handrails [§504.6, §505]
Handrails [§504.6, §505] Handrails are required on both sides of stairs and must be continuous within the full length of each stair flight. Inside handrails on switchback or...
