Writing surfaces must be 36 inches maximum from the floor....
Search Results "Transfer Surface"
-
Check-Out Aisles [7.3]
-
§ 35.151(e)(2)
Transfer-type showers are not permitted in lieu of a roll-in shower with a seat, and the exceptions in sections 608.3 and 608.4 for residential dwelling units are not permitted....
-
Access Board: Accessible Bathing Facilities Scoping
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
Poured in Place Rubber
The surface cost for PIP ranged from $6.59/sq. ft. to $19.80/sq. ft. ...
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
11B-805.7 Built-in cabinets and work surfaces
Built-in cabinets, counters and work surfaces shall be accessible, including: patient wardrobes, nurse’s stations, administrative centers, reception desks, medicine preparation areas, laboratory...
-
Beneficial Designs The Universal Trail Assessment Process (UTAP)
Illustrated step-by-step instructions show how to use each assessment tool, how to accurately measure grade, cross slope , width, and obstacles and how to describe surface type....
-
4.3.3 Slope
When the surface is not paved or is not elevated above the natural ground, slopes not steeper than 1:33 (3 percent) shall be permitted where necessary for drainage. ...
-
Figure 1009.4.3 Depth and Length of Tranfer Walls – Drawing from the U.S. Access Board
-
405.3 Cross Slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
§ 38.125(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
-
2010 ADA Standards - Plan Review Tool - Slopes
2010 ADA Standards - Plan Review Tool - Slopes Click here to view/download the pdf "2010 ADA Standards - Plan Review Tool - Slopes" (774 KB) * * * * * * *
-
1017.6 Openings
Openings in the surface of trails, passing spaces, and resting intervals shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1017.6 Openings. ...
-
1133A.4.1 Exceptions
Two 15-inch (381 mm) wide minimum breadboards may be provided in lieu of the required 30 inches (762 mm) of countertop work surface, and used without meeting the repositioning requirements...
-
1017.6 Openings
This section requires openings in the surface of trails, passing spaces, and resting intervals such as spaces between the boards in a boardwalk to not allow passage of a sphere more than...
-
1017.6 Openings
Openings in the surface of trails, passing spaces, and resting intervals shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1017.6 Openings....
-
1.5 Materials
Four different colors of simulated sidewalk surfaces were used in this study....
-
G. Women's Spa and Fitness Center Locker Room
(3) Defendants will install a transfer wall to permit access to the Women's Whirlpool located in the Quiet Room, pursuant to 2010 Standards §§ 242.4 and 1009.4....
-
Avoid the extremes of surface reflectivity and contrast (slides 11 and 13)
We don’t have to have highly reflective surfaces that will still reflect light but spread it, diffuse that light instead of pinpoint reflections....
-
11B-813.2.1.2 Clearance
Floor or ground surfaces of clearances shall comply with Section 11B-302. Changes in level are not permitted....
-
11B-813.2.1.2 Clearance
Floor or ground surfaces of clearances shall comply with Section 11B-302. Changes in level are not permitted....
-
Built-in Elements
BUILT-IN ELEMENTS Dining/work surfaces 11B-226, 11B-902.2 Benches 11B-903.2...
