Assembly areas shall provide wheelchair spaces, companion seats, and designated aisle seats complying with F221 and 802. In addition, lawn seating shall comply with F221.5....
Search Results "Elevator Car Designation"
-
F221.1 General
-
Design Guidelines for the Visual Environment
This guideline was developed by the Low Vision Design Committee of the National Institute of Building Sciences (NIBS) through initial funding from the U.S....
-
Picnic Units
When designing picnic areas, remember locating 20 percent of the units on an outdoor recreation access route is only a minimum requirement....
-
221.1 General
Assembly areas shall provide wheelchair spaces, companion seats, and designated aisle seats complying with 221 and 802. In addition, lawn seating shall comply with 221.5....
-
1009.10 Directional signage
At elevator landings. Within areas of refuge....
-
1009.10 Directional signage
At elevator landings. Within areas of refuge....
-
Vehicle Spaces: ADA Standard Section 502.2
Section 502.2 covers the current ADA Standards for vehicle spaces.
-
§ 38.93(e) Signage
The International Symbol of Accessibility shall be displaced on the exterior of all doors complying with this section unless all cars are accessible and are not marked by the access symbol...
-
703.5.6 Height from Finish Floor or Ground
EXCEPTION: Visual characters indicating elevator car controls shall not be required to comply with 703.5.6....
-
703.5.6 Height From Finish Floor or Ground
EXCEPTION: Visual characters indicating elevator car controls shall not be required to comply with 703.5.6....
-
409.1 General
Private residence elevators that are provided within a residential dwelling unit required to provide mobility features complying with 809.2 through 809.4 shall comply with 409 and with ASME...
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
407.4.3 Platform to Hoistway Clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
11B-407.4.3 Platform to hoistway clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
407.4.3 Platform to Hoistway Clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1 1/4 inch (32 mm) maximum....
-
Inclusion Solutions Paint Marking Stick
Mark your parking lot for accessibility with this easy to use marking stick Easy assembly and operation Uses: Ideal for parking lots, warehouse aisles, school...
-
§ 38.113(d)(3) Exception
Where platform set-backs do not allow the horizontal gap or vertical alignment specified in paragraph (d) (1) or (2), platform or portable lifts complying with §38.125(b) of this part, or car...
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (13 mm) under rated loading to zero loading conditions....
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
11B-409.4.4 Leveling
Each car shall automatically stop at a floor landing within a tolerance of ½ inch (12.7 mm) under rated loading to zero loading conditions....
-
1009.4.1 Standby power
The elevator shall meet the emergency operation and signaling device requirements of California Code of Regulations, Title 8, Division 1, Chapter 4, Subchapter 6, Elevator Safety Orders....
