The vertical clearance at doorways with lifts, ramps or bridgeplates shall comply with T502.2....
Search Results "Curb Ramp Surface"
Filters
Commonly Searched Documents
-
T502.2 Doorways with Lifts, Ramps or Bridgeplates
-
Doorways at Landings [§405.7.5]
Doorways at Landings [§405.7.5] Required door maneuvering clearances can overlap ramp landings (it is advisable to locate the swing of doors outside ramp landings for greater safety)....
-
5.2.2 Transfer Surface Size for Equipment Used by Patients in Seated Position
5.2.2 Transfer Surface Size for Equipment Used by Patients in Seated Position....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1132A.4, Item 3
Secondary exterior doors onto decks, patios, or balcony surfaces constructed of impervious materials (e.g., concrete, brick, flagstone) may have a maximum change in height from the interior...
-
Inpro Corporation JointMaster® 316 Series Single Sightline for Carpet Floor Expansion Joint Covers
The 316 series system was specially designed for continuous flooring types such as carpet and vinyl sheet. Features & Benefits System reduces joint widths of up to 4"...
-
1009.8 Two-way communication
Two-way communication systems are not required on floors provided with ramps conforming to the provisions of Section 1012....
-
§ 38.83(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
-
M301.2.3.1 End Transfer Surface
End transfer surfaces shall be 28 inches (710 mm) wide minimum and 17 inches (430 mm) long minimum. ...
-
M301.2.3.2 Side Transfer Surface
Side transfer surfaces shall be 28 inches (710 mm) wide minimum and 28 inches (710 mm) long minimum....
-
Populas Vox Two-Story Adjustable Dual Surface Workstation
Standard Features Adjustment range 24” - 50“ Front surface adjustment range 20” - 57” (4” below, 7” above rear surface), with 15 +/- tilt Power adjusted standard 110V, UL Listed...
-
WILLITS, et al v. CITY OF LOS ANGELES - Settlement Terms
Willits v. City of Los Angeles Term Sheet as of March 30, 2015
-
WILLITS, et al v. CITY OF LOS ANGELES - Settlement Agreement and Release of Claims
UNITED STATES DISTRICT COURT CENTRAL DISTRICT OF CALIFORNIA CASE NO. CV 10-5782 CBM (RZx) SETTLEMENT AGREEMENT AND RELEASE OF CLAIMS MARK WILLITS, JUDY GRIFFIN,...
-
11B-250 Circulation paths
[See subsections ...]
-
11B-405.10 Wet conditions
Landings subject to wet conditions shall be designed to prevent the accumulation of water.
-
405.7.1 Slope
Landings shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
-
405.7.1 Slope
Landings shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
-
405.7.1 Slope
405.7.1 Slope. Landings shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted.
-
11B-405.7.1 Slope
Landings shall comply with Section 11B-302. Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted.
-
4.8.5(7)
(7) Handrails shall not rotate within their fittings.
-
4.8.5(3)
(3) The clear space between the handrail and the wall shall be 1 - 1/2 in (38 mm).
-
11B-405.10 Wet conditions
Landings subject to wet conditions shall be designed to prevent the accumulation of water.
-
11B-405.7.1 Slope
Landings shall comply with Section 11B-302. Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted.
-
11B-405.10 Wet conditions
Landings subject to wet conditions shall be designed to prevent the accumulation of water.
