206.2.2 If site conditions have swamp type lands, steep grades, drainage ditches, flood hazards or other inconsistencies with the approved plans, proper methods of compliance...
Search Results "Compliance"
-
Rough Grade Site Inspection
-
BACKGROUND
The City has fully cooperated with the compliance review. ...
-
BACKGROUND
The City has fully cooperated with the compliance review....
-
§ 35.137(c)(2) Inquiry into use of other power-driven mobility device
A “valid” disability placard or card is one that is presented by the individual to whom it was issued and is otherwise in compliance with the State of issuance’s requirements for disability...
-
8. Transportation Vehicles
Compliance with the updated requirements for buses and vans will become mandatory once specified by DOT in a future update of its ADA standards.”...
-
11B-809.5.2 Residential dwelling unit smoke detection system and carbon monoxide detection system
ETA Editor's Note The lengthy California Building Code Chapter 9, Section 907.2.11 referenced above is not adopted by Division of the State Architect - Access Compliance (DSA-AC), and...
-
CHAPTER 35 REFERENCED STANDARDS
ETA Editor's Note Referenced standards not adopted by Division of the State Architect - Access Compliance (DSA-AC) omitted....
-
11B-1008.2.3 Water play components
Exceptions: Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with Sections 11B-302,...
-
11B-809.5.2 Residential dwelling unit smoke detection system and carbon monoxide detection system
ETA Editor's Note The lengthy California Building Code Chapter 9, Section 907.2.11 referenced above is not adopted by Division of the State Architect - Access Compliance (DSA-AC), and...
-
CHAPTER 35 REFERENCED STANDARDS
ETA Editor's Note Referenced standards that are not adopted by Division of the State Architect - Access Compliance (DSA-AC) have been omitted....
-
11B-207.1 General
The IEBC is not adopted by the Division of the State Architect for access compliance. Therefore the provision will now be located in Section 11B-207.1. ◼...
-
2. Types of Electronic Respiratory Assistive Devices
In addition, section 382.9 allows a foreign carrier to petition the Department for a waiver of compliance with any provision in Part 382, including section 382.133, if an applicable foreign...
-
Are the elements of path of travel and accessible routes substantively the same (such as slope, vertical clearance, width of path of travel, etc.)?
These elements are required to comply with the current code requirements or be brought into compliance when an alteration occurs....
-
Implementation and Enforcement
Compliance Review and Enforcement. The United States may review LCG’s compliance with this Agreement or title III of the ADA at any time. ...
-
3.2.2.1. Low Accessibility Baseline
in 2015** = Low Access-ibility Baseline Number of Audito-riums Exhibiting Digital Movies Equipped to Provide Captioning/ Audio Description in Compliance...
-
Final Regulatory Flexibility Analysis
All small entities currently in compliance with the 1991 Standards will neither need to undertake further retrofits nor require the services of a consultant to tell them so....
-
Safe Harbor is applied element by element in existing facilities
Do all of the existing elements of that type in the facility have to be considered for modification to bring those elements into compliance with all of the additional requirements in the...
-
FAA Advisory Circular 150/5360-14: Access to Airport by Individuals with Disabilities
This AC includes legal citations, the effective dates of regulations, and compliance dates to assist the reader in differentiating between the requirements of the applicable statutes and...
-
EXHIBIT A Required Accessible Elements at QuikTrip Stores
Accessible routes shall be provided in compliance with ADA Standards §§ 4.1.2(1), 4.1.3(1), and 4.3, including the following requirements: a....
-
Boat Slip Clearance: ADA Standard Section 1003.3.1
be permitted to be located perpendicular to the boat slip and shall extend the width of the boat slip, where the facility has at least one boat slip complying with 1003.3, and further compliance...
-
Construction and Manufacturing Tolerances: ADA Standard Section 104.1.1
Section 104.1.1 of the ADA Standards covers the most current information on dimensions in regards to construction and manufacturing tolerances in the ADA Standards.
-
11B-1003.3.1 Boat slip clearance
permitted to be located perpendicular to the boat slip and shall extend the width of the boat slip, where the facility has at least one boat slip complying with Section 11B-1003.3, and further compliance...
-
11B-1003.3.1 Boat slip clearance
permitted to be located perpendicular to the boat slip and shall extend the width of the boat slip, where the facility has at least one boat slip complying with Section 11B-1003.3, and further compliance...
