Clear floor spaces 30 inches (762 mm) by 48 inches (1219 mm), with centerlines aligned with the centerline of the work surface, appliance, sink or fixture, shall be provided in the following...
Search Results "Check Writing Surface"
-
11B-809.9.1 Clear floor space
-
203.9 Employee Work Areas
Spaces and elements within employee work areas shall only be required to comply with 206.2.8, 207.1, and 215.3 and shall be designed and constructed so that individuals with...
-
Height – M301.2.1 & M302.2.1
Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic...
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface where...
-
5.3.2.2 Transfer Sides Recommendation for Imaging Equipment
5.3.2.2 Transfer Sides Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface on which patients are in the...
-
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Key Study findings:
When multiple transfers are required to reach higher or lower surfaces 15.2% of the participants in this study could not complete them at any height (11 out of 72 participants; 8 of which...
-
Section B: Passenger Drop-Off Area
Yes No N/A Comments/Remedies B1 Is the vehicle pull-up space on a level surface, with slopes not exceeding 1:48 in all directions?...
-
Balco FMS-A Floor Mat with Extruded Vinyl Edge Section
Requires the Premium User plan or above. (Login or upgrade your account!) -
8.3 Check-Out Areas
At least one lane at each check-out area shall comply with 7.2(1). Any traffic control or book security gates or turnstiles shall comply with 4.13....
-
Figure 505.7.2 Handrail Non-Circular Cross Section – Drawing from the U.S. Access Board
-
M305.3.1 Length (Section-by-Section Analysis)
In the MDE NPRM, the Access Board proposed a gripping surface length of four inches minimum for horizontal standing supports. No public comments were submitted on this requirement....
-
5.3.2 Transfer Sides Recommendations for M301
the long side of the surface....
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
3. Do requests for reasonable accommodation need to be in writing?
Requests for reasonable accommodation do not need to be in writing....
-
Check Optional Features, if available
Check Optional Features, if available Pushbutton information message - Press the pushbutton for an extended button press to see if the pushbutton information message plays and that it...
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
1.1.7 Measurement of parking areas
1.1.7 Measurement of parking areas. Only accessible access aisles and passenger loading zones that are part of a larger parking area need to be measured. These areas should be...