Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1219 mm) maximum and the low side...
Search Results "Parallel Grab Bar"
-
11B-308.3.1 Unobstructed
-
11B-406 Curb ramps, blended transitions and islands
Parallel curb ramps and blended transitions, although permitted by 2010 ADA Standards, are not defined or given special attention....
-
11B-812.6 Vehicle spaces
Exceptions: Where the long dimension of vehicle spaces is parallel to the traffic flow in the adjacent vehicular way, the length of vehicle spaces shall be 240 inches (6096 mm) minimum...
-
Yale 1100 Series Industrial Door Closer
closers are adjustable spring sizes 1 through 4 • 1104BC (non-hold open) door closers are spring size 4 • Non-handed • Full rack and pinion • Aluminum • Tri-packed: regular, parallel...
-
Yale 2700 Series Architectural Door Closer
Features: • Adjustable spring sizes 1 through 6 • Non-handed • Aluminum • Tri-packed: regular, parallel or top jamb mounting • Adjustable backcheck valve • Adjustable closing...
-
Palmer Fixture BluStorm® Bolt High Speed Hand Dryer HD0923
Adjustable sensor and air speed Dries hands in 15 seconds On/Off heater switch - runs on only 4 amps with heater off Patented parallel dual air outlets - high drying...
-
3. The Release Provisions are Overbroad
The release provisions are overbroad in three significant respects, they: a) appear to waive access claims arising after the date of the settlement agreement; b) bar state and local law...
-
1008.3.2.3 Transfer Supports
Some examples of supports include a rope loop, a loop type handle, a slot in the edge of a flat horizontal or vertical member, poles or bars, or D rings on the corner posts....
-
11B-104.1.1 Construction and manufacturing tolerances
Where the requirement states a specified range, such as in Section 11B-609.4 where grab bars must be installed between 33 inches and 36 inches above the floor, the range provides an adequate...
-
ASME
The enclosure walls not used for entry or exit are required to have a grab bar the full length of the wall on platform lifts....
-
11B-104.1.1 Construction and manufacturing tolerances
Where the requirement states a specified range, such as in Section 11B-609.4 where grab bars must be installed between 33 inches and 36 inches above the floor, the range provides an adequate...
-
9.b [§ 4.7.5]
The level should be placed so that it is parallel to the curb. Place the level in the same position and location as each of the arrows in the illustration to the left [below]....
-
11B-307.4 Vertical clearance
Where a guy support is used parallel to a circulation path, including but not limited to sidewalks, a guy brace, sidewalk guy or similar device shall be used to prevent an overhanging obstruction...
-
13 [§ 4.7.10]
When taking this measurement, the measuring tape should be aligned parallel to the ramp run itself and should stretch from the intersection of the ramp and gutter to the innermost edge of...
-
11B-406 CURB RAMPS, BLENDED TRANSITIONS AND ISLANDS
Parallel curb ramps and blended transitions, although permitted by 2010 ADAS, are not defined or given special attention. ...
-
308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1220 mm) maximum and the low side...
-
406.6 Diagonal Curb Ramps
Diagonal or corner type curb ramps with returned curbs or other well-defined edges shall have the edges parallel to the direction of pedestrian flow....
-
11B-502.6.4.2
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1220 mm) maximum and the low side...
-
308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1220 mm) maximum and the low side...
-
Unified Facilities Guide Specifications
published by the National Institute of Building Sciences, it is stated that surfaces should be tested with a 4 - meter (12 ft) straightedge in both a longitudinal and transverse direction on parallel...
-
11B-308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1219 mm) maximum and the low side...
-
11B-307.4 Vertical clearance
Where a guy support is used parallel to a circulation path, including but not limited to sidewalks, a guy brace, sidewalk guy or similar device shall be used to prevent an overhanging obstruction...
-
11B-809.10.5.1 Clear floor space
A clear floor space 30 inches (762 mm) minimum by 48 inches (1219 mm) minimum shall be located with the long edge of the clear floor space parallel to the side of the bathtub or bathtub-shower...
