Knee and toe clearance complying with 306 shall be provided....
Search Results "Vertical Clearance"
Filters
Commonly Searched Documents
-
902.2 Clear Floor or Ground Space
-
2.7 Tread Obstacles
Where the surface is paved or is elevated above the natural ground, obstacles shall not exceed 1/2 inch (13 mm) in height measured vertically to the highest point. ...
-
§ 38.73(d)(4) Exception
Where it is not operationally or structurally practicable to meet the horizontal or vertical requirements of paragraphs (d) (1), (2) or (3) of this section, platform or vehicle devices complying...
-
11B.707.7.1.3 Horizontally mounted display screen
Where display screens are mounted tipped away from the viewer 60 degrees to 90 degrees (horizontal) from vertical, the center line of the display screen and other display devices shall be...
-
Pilot Rock WPTS Square Frame Picnic Table Using Formed Steel Channel
Model WPTS 8 ft table offers clearances under the table top of 30" wide, 27" high, and 24" total knee and toe clearance (19" knee + 5" toe). Nominal seat height is 18". ...
-
Pilot Rock WPTS Square Frame Table Using Aluminum
Model WPTS 8 ft table offers clearances under the table top of 30" wide, 27" high, and 24" total knee and toe clearance (19" knee + 5" toe). Nominal seat height is 18". ...
-
Grab Bars
If only one bar is provided, the clearance must be a minimum of 24 inches on each side of the bar....
-
1009.4.5 Grab Bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
11B-810.5.3 Platform and vehicle floor coordination
In light rail, commuter rail, and intercity rail systems where it is not operationally or structurally feasible to meet the horizontal gap or vertical difference requirements of part 1192...
-
A) Accessible Parking
the same requirements as accessible parking spaces for cars and have three additional features for vans: • a wider access aisle (96 inch-wide) to accommodate a wheelchair lift; • vertical...
-
AISLE
., that provides clearances in in compliance with this code....
-
AISLE
., that provides clearances in compliance with this code....
-
BACKGROUND
recommendation: 5.4.11 Transfer Support Structural Strength Recommendations for M301 and M302 Description: Transfer supports and their connections must be capable of resisting sufficient vertical...
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
§ 38.125(b)(4) Power or equipment failure
Platforms stowed in a vertical position, and deployed platforms when occupied, shall have provisions to prevent their deploying, falling, or folding any faster than 12 inches/second or their...
-
§ 38.95(b)(4) Power or equipment failure
Platforms stowed in a vertical position, and deployed platforms when occupied, shall have provisions to prevent their deploying, falling, or folding any faster than 12 inches/second or their...
-
§ 38.23(b)(4) Power or equipment failure
Platforms stowed in a vertical position, and deployed platforms when occupied, shall have provisions to prevent their deploying, falling, or folding any faster than 12 inches/second or their...
-
11B.707.7.1.2 Angle-mounted display screen
Where display screens are mounted tipped away from the viewer 30 degrees to less than 60 degrees from vertical, the center line of the display screen and other display devices shall be no...
-
11B-703.7.2.6 Toilet and bathing facilities geometric symbols
Where a door is provided the symbol shall be mounted within 1 inch (25 mm) of the vertical centerline of the door....
-
11B-1002.4.3 Gaps
Floors of amusement rides with wheelchair spaces and floors of load and unload areas shall be coordinated so that, when amusement rides are at rest in the load and unload position, the vertical...
-
Magnuson Group WH Hanger Style Wall Rack
One or two shelves can be vertically adjusted in their steel channels to provide needed space between shelves and appropriate hanging distance to the floor....
-
11B-407.4.10.3 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the support rail, fastener, mounting device...
-
Running Slope (Grade)
This may be expressed as a ratio of vertical distance to horizontal distance or as the percentage of change in elevation. ...
-
7.4.4.4 Turning Space
Vertical alignment between the trail tread, turning space, and resting interval shall be nominally level. The trail tread, turning space, and resting interval may overlap....
