distribution of goods to the public, an auxiliary counter or a portion of the main counter shall be provided with a maximum height of between 28 in to 34 in (710 mm to 865 mm) above the floor in compliance...
Search Results "OOC: Office of Compliance"
Filters
Commonly Searched Documents
-
7.2 SERVICE COUNTERS
-
68.10(18) Owner
For purposes under these rules and the Act, an owner may designate an agent; however, the owner remains responsible for compliance with the Act....
-
§ 38.111(a)(1)
Compliance with §38.125 of this part shall be required only to the extent necessary to meet the requirements of paragraph (d) of this section....
-
Water Play Components: ADA Standard Section 1008.2.3
Where the surface of the accessible route, clear floor or ground spaces, or turning spaces serving water play components is submerged, compliance with 302, 403.3, 405.2, 405.3, and 1008.2.6...
-
11B-705.1.2.2.2.2 Two entrance/exit points
Existing parallel curb ramps with detectable warnings in compliance with the code requirements in effect at the time of installation shall not be required to provide a minimum 36 inches...
-
11B-235.2.1 Dispersion
For example, a fuel pier may contain boat slips, and this type of short term slip would be included in determining compliance with Section 11B-235.2. ◼...
-
11B-1002.4.3 Gaps
Exception: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
11B-233.3.4 Alterations
Exception: Where compliance with Sections 11B-809.2, 11B-809.3, or 11B-809.4 is technically infeasible, or where it is technically infeasible to provide an accessible route to a residential...
-
Enactment of the ADA and Issuance of the 1991 Regulations
generally open to the public and that fall into one of 12 categories listed in the ADA, such as restaurants, movie theaters, schools, day care facilities, recreation facilities, and doctors’ offices...
-
11B-608.3 Grab bars
Grab bars shall not be required to be installed in a shower located in a bathing facility for a single occupant accessed only through a private office, and not for common use or public use...
-
3001.3 Accessibility
108.2.1.2 regulated by the Department of Housing and Community Development or Chapter 11B for applications listed in Section 1.9.1 regulated by the Division of the State Architect─Access Compliance...
-
ADA Coordinator
engineer, with the requisite credentials, such as CASP certification, and no less than five years’ experience, and employed by the City within the first 12 months after commencement of the Compliance...
-
§104.9 Administrative requirements for small recipients.
fifteen employees, or any class of such recipients, to comply with §§104.7 and 104.8, in whole or in part, when the Assistant Secretary finds a violation of this part or finds that such compliance...
-
Section 3. Fair Housing Act Design and Construction Requirements
A reprint of §100.205 was included to provide easy reference to (1) the Act's accessibility requirements, as codified by §100.205; and (2) the additional examples of methods of compliance...
-
§8.57(a) General
If there appears to be a failure or threatened failure to comply with this part and if the noncompliance or threatened noncompliance cannot be corrected by informal means, compliance with...
-
1002.4.7.1 Shoulder-to-Shoulder Seating
EXCEPTION: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
Doors
Recommendation: Compliance with 4.13.6 is recommended because while wider door openings may facilitate access, they do not fully compensate for latch-side clearance, particularly on the...
-
Can a more recent edition of the ASME A17.1 Safety Code for Elevators and Escalators (or the ASME A18.1 Safety Standard for Platform Lifts and Stairway Chairlifts) be used instead of the editions referenced in the Standards?
Compliance with a later edition may be possible under the provision for “equivalent facilitation” (§103) if it is comparable to, or stricter than, the referenced editions....
-
Cities and Counties: First Steps Toward Solving Common ADA Problems
First Steps Toward Solving Common ADA Problems Through its Project Civic Access initiative, the Department has worked with over 100 State and local governments to bring them into compliance...
-
9. Release of Claims
Released Claims Up to the Commencement of the Compliance Period Effective upon the entry of Judgment by the District Court, Plaintiffs and the Settlement Class members (and their respective...
-
TownSteel MSE-32-II Classroom Intruder with Indicator on Inside Mechanical Mortise
The MS series Mortise Lock with Indicator is designed for High Traffic commercial areas such as schools, universities hotels, office buildings, and industrial complexes....
-
TownSteel XME9040 Mortise, Clutched Trim Security Cylinder Mortise Keypad
XME-9040 SPECIFICATION Electronic Specifications Application: For classroom lockdown, full indoor and outdoor User/Office code capacity per lock : 90 Emergency code capacity per lock...
-
Relationship to Other Laws
Compliance with the Department's ADA regulations does not ensure compliance with other Federal statutes....
