permitted", such as 304.2 for turning spaces: Here the standard is followed by an unenforceable advisory that says, "As used in this section, the phrase ‘changes in level’ refers to surfaces...
Search Results "Curb Ramp Surface"
-
2) Where the Standard says "Changes in level are not permitted"
-
§ 38.95(c)(3) Ramp threshold
(3) Ramp threshold....
-
Pemko 193 Slip resistance
By slip resistance I am assuming it will meet the coefficient of friction requirement of 0.8 if installed on a ramp. Thank you -Brian...
-
Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry
Access Board RE: Analysis of Transfer Surface Dimensions Based on Wheeled Mobility User Anthropometry...
-
11B-226.2 Dispersion
Dining surfaces required to comply with Section 11B-902 shall be dispersed throughout the space or facility containing dining surfaces for each type of seating in a functional area....
-
11B-226.2 Dispersion
Dining surfaces required to comply with Section 11B-902 shall be dispersed throughout the space or facility containing dining surfaces for each type of seating in a functional area....
-
11B-226.2 Dispersion
Dining surfaces required to comply with Section 11B-902 shall be dispersed throughout the space or facility containing dining surfaces for each type of seating in a functional area....
-
5.2.2.2 Transfer Surface Depth
5.2.2.2 Transfer Surface Depth. The transfer surface should be 17 inches deep minimum for equipment used by patients in a seated position....
-
226.2 Dispersion
Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces....
-
226.2 Dispersion
Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces....
-
F226.2 Dispersion
Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces. [ECTCR UFAS 5.1]...
-
5.2.2.1 Transfer Surface Width
5.2.2.1 Transfer Surface Width. The transfer surface should be 21 inches wide minimum for examination chairs and other equipment used by patients in a seated position....
-
6. Recognize that Proper Installation of Play Surface Systems is Key
Recognize that Proper Installation of Play Surface Systems is Key An accessible surface system can be rendered useless if it is not properly installed....
-
4.8.4* Landings
Ramps shall have level landings at bottom and top of each ramp and each ramp run. Landings shall have the following features:...
-
§ 38.159(c)(8) Handrails
to grasp them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches (760 mm) above the ramp...
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground.
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground.
-
Accessible Ground Surfaces
Accessible Ground Surfaces Ground surfaces along accessible routes, clear floor or ground spaces, and maneuvering spaces, must comply with the American Society for Testing and Materials...
-
Mirror Height
The guidelines specify that accessible mirrors be mounted so that the bottom edge of the reflecting surface is no higher than 40 inches (603.3)....
-
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report December 2014 Human Engineering Research Laboratories VA Pittsburgh Healthcare System...
-
Where do I measure for a handrail extension?
Handrail gripping surfaces shall extend beyond and in the same direction of stair flights and ramp runs in accordance with 505.10. ...
-
§ 37.42(f)
vertical gap is more than 5/8 inch, measured when the vehicle is at rest, the horizontal and vertical gaps between the car floor and the boarding platform must be mitigated by a bridge plate, ramp...
-
Madden Manufacturing Round Handrail (ADA Compliant)
Contractor ADA Handrail is an innovator in mechanical ADA fittings and systems. Available in kit form or full length extrusions, each system is carefully designed and packaged to...
