Clear ground space width Maximum doorway depth and passage width Turning space: C1. Accessible route turns around an obstruction: C2....
Search Results "Maximum Dimension"
-
2. a. iv. Path-of-Travel (wheelchair) space allowances
-
609.4 Position of Grab Bars
Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
11B-602.2 Clear floor space
Exception: A parallel approach complying with Section 11B-305 shall be permitted at units for children's use where the spout is 30 inches (762 mm) maximum above the finish floor or ground...
-
11B-604.9.6 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 _|Operation|_ and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the...
-
11B-604.9.1 Location
The centerline of the water closet shall be 12 inches (305 mm) minimum and 18 inches (457 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (432...
-
§ 38.123(a)(1)
Permanently installed fixtures may overlap this area a maximum of 6 inches, if the lowest portion of the fixture is a minimum of 9 inches above the floor, and may overlap a maximum of 19...
-
610.2 Bathtub Seats
The top of bathtub seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor....
-
904.4.1 Parallel Approach
A portion of the counter surface that is 36 inches (915 mm) long minimum and 36 inches (915 mm) high maximum above the finish floor shall be provided....
-
609.4 Position of Grab Bars
Grab bars shall be installed in a horizontal position, 33 inches (840 mm) minimum and 36 inches (915 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
1009.3.2 Submerged Depth
Sloped entries shall extend to a depth of 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level....
-
§35.151(d)(1)
(1) Alterations to historic properties shall comply, to the maximum extent feasible, with §4.1.7 of UFAS or §4.1.7 of ADAAG....
-
§35.151(e)(1)
(1) Alterations to historic properties shall comply, to the maximum extent feasible, with §4.1.7 of UFAS or §4.1.7 of ADAAG....
-
1011.8 Viewing Scopes
This section requires eyepieces on viewing scopes to be 43 inches minimum and 51 inches maximum above the ground....
-
407.4.8.2.3 Frequency
The verbal annunciator shall have a frequency of 300 Hz minimum to 3000 Hz maximum....
-
Pilot Rock PQT3-4 Square Pedestal Table Using Aluminum
Table offers 32" table height, 20" seat height (nominal dimensions). FRAME: Supported by one central, massive 5-3/8" sq. steel post. ...
-
11B-608.5.3 Alternate roll-in type shower compartments
shower compartments, the controls, faucets, and shower spray unit shall be located on the side wall of the compartment adjacent to the 16 inches (406 mm) minimum and 27 inches (686 mm) maximum...
-
Elvoron LU/LA - Limited Use / Limited Application Hydraulic Elevator
Limited Use, Limited Application 25 feet (7.6 m) maximum travel* 18 square feet (1.67 m2) maximum car size 30 feet per minute maximum speed* 1400 lbs...
-
Omnia Industries Inc. Interior Modern Lever Latchset - Stainless Steel No.47
Interior Modern Lever Latchset - Stainless Steel Dimensions: 3" Projection x 5- 1/2 " Length, 11/16" Lever Diameter Finishes: US32D...
-
11B-409.4.3 Platform to hoistway clearance
The clearance between the car platform and the edge of any landing sill shall be 1½ inch (38 mm) maximum....
-
11B-410.4 Platform to runway clearance
The clearance between the platform sill and the edge of any runway landing shall be 1¼ inch (32 mm) maximum....
-
1008.2.5.2 Elevated
The rise for any ramp run connecting elevated play components shall be 12 inches (305 mm) maximum....
-
410.4 Platform to Runway Clearance
The clearance between the platform sill and the edge of any runway landing shall be 1 inch (32 mm) maximum....
-
409.4.3 Platform to Hoistway Clearance
The clearance between the car platform and the edge of any landing sill shall be 1-½ inch (38 mm) maximum....
-
703.5.7 Stroke Thickness
Stroke thickness of the uppercase letter "I" shall be 10 percent minimum and 30 percent maximum of the height of the character....
