The top of handrail gripping surfaces shall be 20 inches (508 mm) minimum and 28 inches (711 mm) maximum above the ramp surface....
Search Results "Gripping Surface"
Filters
Commonly Searched Documents
-
11B-1008.2.5.3.2 Handrail height
-
FIGURE 11A-10A KITCHEN SPECIFICATIONS
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical...
-
Bathroom Do’s and Dont’s
Do. Use a floor drain that extends the length of the shower to prevent water flowing into other areas of the bathroom. This is recommended, even if the floor is sloped near the...
-
1133A.1 General
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
Engineered Surfaces
The engineered surfaces consisted of a 16ft x 4ft runway with a 4ft x 4ft flat platform on each end....
-
R310.3.4 Surfaces
R310.3.4 Surfaces. Access aisle surfaces shall comply with R302.7....
-
1009.4.4 Surface
1009.4.4 Surface. Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
1009.5.5 Surface. The surface of the transfer system shall not be sharp and shall have rounded edges....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer surface...
-
Position of Grab Bars: ADA Standard Section 609.4
Section 609.4 covers the current ADA Standards for the position of grab bars.
-
11B-609.4 Position of grab bars
Grab bars shall be installed in a horizontal position, 33 inches (838 mm) minimum and 36 inches (914 mm) maximum above the finish floor measured to the top of the gripping surface, except...
-
M305.2.1 Location (Section-by-Section Analysis)
surface depths of greater than 24 inches....
-
Clearances between a handrail and wall surface: 2012 NFPA 101 vs. 2010 ADA
finger clearance at an existing stair handrail should be greater than or equal to 2-1/4” which conflicts with the 1.5" clearance in 2010 ADA section 505.5 regarding the distance between the gripping...
-
d. Unobstructed Transfer
The MDE NPRM proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they could be repositioned...
-
Sloped Surfaces
Measuring the slope of a ramp, parking space, pedestrian route, or other ground or floor surface is important to identify whether the surface is accessible....
-
11B-224.7 Housing at a place of education
and clustered sleeping rooms) or on floors containing accessible sleeping rooms with mobility features shall provide turning spaces that comply with Section 11B-809.2.2 and kitchen work surfaces...
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
Transfer supports should be required on both sides of the transfer surface and be movable or removable so they can be out of the way during transfer....
-
5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302
provide options to transfer onto the short side and the long side of the surface....
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
The transfer support should be a minimum length of 15 inches positioned so that the transfer support overlaps the minimum depth of the transfer surface by 80%....
-
1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....