Turnstiles and Security Gates at Entrances Businesses with narrow revolving turnstiles located at the entrance exclude people with disabilities unless accessible gates or passages...
Search Results "Curb Ramp Width"
-
Turnstiles and Security Gates at Entrances
-
T502.3 Doorways with Level Boarding
Doorways on non-rail vehicles designed for level boarding bus systems shall comply with T502.3.
-
G. Drop-off Area
G. If the lodging facility has covered passenger pickup/drop-off areas, does the pavement at such area(s), including the required 5' wide access aisle, slope 1:50 or less (critical...
-
§ 36.304(b)(9)
(9) Installing offset hinges to widen doorways;
-
Sec.36.304(b)(9)
(9) Installing offset hinges to widen doorways;
-
9.2.2(3)
(3) Doors and doorways designed to allow passage into and within all sleeping rooms, suites or other covered units shall comply with 4.13.
-
9.4 Other Sleeping Rooms and Suites
Doors and doorways designed to allow passage into and within all sleeping units or other covered units shall comply with 4.13.5.
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10....
-
11B-406.2.2 Sides of curb ramps
Where provided, curb ramp flares shall not be steeper than 1:10....
-
5.9.2.1 Standing Supports on Single Ramped Entry Raised Platforms with Wheelchair Spaces
5.9.2.1 Standing Supports on Single Ramped Entry Raised Platforms with Wheelchair Spaces....
-
5.9.2.2 Standing Supports on Dual Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations
integrated into the platform and stretching the full length of the platform (40-inch minimum) for dual ramped entry raised platforms....
-
Feature 2 - Routes to the Building Entrance
Where ramps are used, they cannot be steeper than 1:12 (8.33% incline). Ramps with a vertical rise of more than 6 inches must have handrails on both sides....
-
11B-809.8 Doors
The clear width of doors shall comply with Section 11B-404.2.3. Door hardware shall comply with Section 11B-404.2.7. Door surfaces shall comply with Section 11B-404.2.10....
-
Rockwood Manufacturing Company 700 Handrail Bracket
Material: Cast Brass FASTENER: Wood Rail: 5/16-18 x 1-1/2 FH MS, Lead Anchor; 3 ea. 12-24 x 1 FH MS; 2 ea. #8 x 3/4 OH SMS; 1 ea. Back Plate Metal Rail: 5/16-18 x 1-1/2 FH...
-
Rockwood Manufacturing Company 702 Handrail Bracket
Specifications: Material: Cast Brass FASTENER: Wood Rail: 3 ea. #12 x 2 FH WS; 2 ea. #8 x 3/4 OH SMS Metal Rail: 3 ea. #12 x 2 FH WS; 2 ea. 8-32 x 3/4 OH SMS Ordering: ...
-
11B-224.1.2 Guest room doors and doorways
Because of the social interaction that often occurs in lodging facilities, an accessible clear opening width is required for doors and doorways to and within all guest rooms, including those...
-
4.8.6 Cross Slope and Surfaces
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.8.6 CROSS SLOPE AND SURFACES
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
III-6.2000 Alterations: Path of travel
Because the most important path of travel element is the entrance and route to the area, the library should spend the money on the ramp, telephones, and drinking fountains....
-
§ 38.125(c)(6)(i) Requirement
When in use for boarding or alighting, the ramp or bridge plate shall be attached to the vehicle, or otherwise prevented from moving such that it is not subject to displacement when loading...
-
The Corada Shop
-
T202.1 General
Provision of accessible boarding and alighting shall be made through one or more of the following methods: ramps or bridgeplates complying with T402, lifts complying with T403, or a means...
-
4.1.7(3)(a)
EXCEPTION: A ramp with a slope no greater than 1:6 for a run not to exceed 2 ft (610 mm) may be used as part of an accessible route to an entrance....
