Water Closet Centerline 12 inches (305 mm) 12 to 15 inches(305 to 380 mm) 15 to 18 inches(380 to 455 mm) Toilet Seat Height...
Search Results "Bed Height"
Filters
Commonly Searched Documents
-
604.9 Water Closets and Toilet Compartments for Children’s Use
-
703 Signs
Requirements for signs provide specifications for raised characters (703.2), braille characters (703.3), the height and location of signs with tactile characters (703.4), visual characters...
-
Toilet Paper Dispensers
Requirements for toilet paper dispensers in section 604.7 include specifications for height....
-
604.9 Water Closets and Toilet Compartments for Children's Use
Ages 9 through 12 Water Closet Centerline 12 inches (305 mm) 12 to 15 inches (305 to 380 mm) 15 to 18 inches (380 to 455 mm) Toilet Seat Height...
-
604.9 Water Closets and Toilet Compartments for Children’s Use
8 Ages 9 through 12 Water Closet Centerline 12 inches (305 mm) 12 to 15 inches (305 to 380 mm) 15 to 18 inches (380 to 455 mm) Toilet Seat Height...
-
3.3.15.1 Forward reach – unobstructed
Lower percentages in a forward reach for scooter users partially resulted from having to overcome a greater distance to reach over and/or around the front tiller, particularly at lower heights...
-
Protruding Objects
All objects that protrude from surfaces or posts and all overhanging objects in areas where people walk shall comply with the following requirements: Objects mounted on walls at a height...
-
R410.9 Character Spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
703.5.8 Character Spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
R405.3.4 Clearance Reduction
Between 230 mm (9 in) and 685 mm (2.25 ft) above the finish surface, the knee clearance shall be permitted to reduce at a rate of 25 mm (1 in) in depth for each 150 mm (6 in) in height....
-
Do drinking fountains pose hazards as protruding objects?
Cantilevered units at standard heights for people who stand must be recessed or protected as protruding objects....
-
Character Specifications
For characters with rectangular cross sections, a stroke thickness of 10% to 15% of the character height was specified (based on the uppercase "I")....
-
Doors in a Series
The height of door and gate hardware (34 to 48 inches) is specified in section 404.2.7....
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
Introduction
Footrest clearance height and depth...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
11B-703.5.8 Character spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
203.6 Single Occupant Structures
Single occupant structures accessed only by passageways below grade or elevated above standard curb height, including but not limited to, toll booths that are accessed only by underground...
-
4. Shower Wand
Is there an adjustable height hand-held shower wand with at least a 60" long hose provided so persons who bathe from a seated position may wash and rinse with the directional spray?...
-
2. Using the Tape Measure
Using the Tape Measure A metal tape measure is needed to measure the length, width, height, and depth of various elements....
-
502.2.1 On-street parallel parking
Curbs adjacent to such spaces must be of a height that does not interfere with the opening and closing of motor vehicle doors. Figure 502.2 Vehicle Parking Spaces...
-
Food and Beverage Service
Accommodating Diners with Disabilities factsheet provides both legal standards and promising practices for paths of travel, approach to dining spaces, seating, dining table and service counter heights...