horizontal discontinuities and variations in vertical alignment such as at concrete joints, gaps, grade breaks, and at the interface of concrete with other materials or elements built into the surface...
Search Results "Trail Surface"
Filters
Commonly Searched Documents
-
1.1.9 Horizontal gaps and vertical alignment
-
Bosch Five-Point Self-Leveling Alignment Laser GPL 5 S
Description The GPL 5S is a five-point laser that levels, plumbs up, plumbs down, and squares. It accurately transfers and aligns level, plumb and 90 degree square points. With...
-
Bosch 3-Point Self-Leveling Alignment Laser GPL 3
Description Three-point plumb and level point projection laser accurately transfers and aligns plumb up/down, front level and align points; accuracy is +/- 1/4 In. at 100 ft....
-
Bosch 3 Point Self Leveling Alignment Laser Level GPL 3 S
Description The GPL3 offers limitless uses, everything from plumbing up floors and ceilings to installing drywall partitions and establishing benchmarks. And because it can be...
-
F202.4 Alterations Affecting Primary Function Areas
Camping facilities, picnic facilities, viewing areas, trailheads, trails, and beach access routes shall not be required to comply with F202.4....
-
Exceptions When Conditions Do Not Permit Full Compliance
permits exceptions based on the conditions to any provision in the technical requirements for tent pads and tent platforms, camp shelters, viewing areas, outdoor recreation access routes, trails...
-
T503.5 Exterior Illumination for Boarding and Alighting Areas
Exterior lighting shall be provided to illuminate walking surfaces of boarding and alighting areas when the doors of non-rail vehicles are open....
-
Cross Slope
Cross Slope The cross slopes of gangways, transition plates and floating piers that are part of an accessible route must be designed and constructed not to exceed a maximum of 2...
-
Addendum D: Comparison of demographics and transfer height between Phase 1 and Phase 2 of the study
[See subsections ...]
-
4.3.7 Slope
An accessible route with a running slope greater than 1:20 is a ramp and shall comply with 4.8. Nowhere shall the cross slope of an accessible route exceed 1:50.
-
4.3.7 SLOPE
An accessible route with a running slope greater than 1:20 is a ramp and shall comply with 4.8. Nowhere shall the cross slope of an accessible route exceed 1:50.
-
Electronic instruments
Electronic instruments have been developed to measure floor flatness. Originally created to measure the flatness of concrete floors in critical applications such as narrow - aisle...
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance
-
2. Is this trail primarily surfaced with a material other than asphalt, concrete, or boardwalk?
Is this trail primarily surfaced with a material other than asphalt, concrete, or boardwalk? Yes No If “No” is selected, then skip to “End of Survey” (Qualtrics Option)....
-
5.4.2.2 Transfer and Positioning Support Length for Imaging Equipment with Transfer Surfaces
5.4.2.2 Transfer and Positioning Support Length for Imaging Equipment with Transfer Surfaces....
-
Wheeled Mobility Anthropometry Project
The data and recommendations from the Wheeled Mobility Anthropometry Project are discussed in connection with the following technical criteria: • Height of transfer surfaces on diagnostic...
-
Smith Carrel Hi-Lo Study Carrel - "The Original"
Includes (2) 3" diameter cutouts for wiring along with a CPU Holder (shelf) located under the work surface. This quality unit is now "ADA Compliant"....
-
Gripping Surface Cross Section and Clearances M301, M302, and M305.2
Gripping Surface Cross Section and Clearances M301, M302, and M305.2 Gripping surface for transfer supports shall be free of sharp or abrasive elements and shall have rounded edges per...
-
M305.3.2.1 Horizontal Position
The height of the top of the gripping surface on horizontal standing supports shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
M302.2.5 Unobstructed Transfer
Each transfer side complying with M302.2.4 shall provide unobstructed access to transfer surfaces. EXCEPTIONS: 1....
-
Implication for Standards and Design
The station used in this second phase permitted greater freedom of wheelchair positioning around the transfer surface compared to the first phase station. ...
-
§ 38.115(a)
The diameter or width of the gripping surface of interior handrails and stanchions shall be 11/4 inches to 11/2 inches or shall provide an equivalent gripping surface....
-
M302.2.5 Unobstructed Transfer (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they...
-
§ 38.23(b)(13) Handrails
The handrail shall have a cross-sectional diameter between 11/4 inches and 11/2 inches or shall provide an equivalent grasping surface, and have eased edges with corner radii of not less...
