5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2 Description: This provision prescribes a cross-sectional profile of the transfer support...
Search Results "Positioning Support"
-
5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2
-
11B-411.4.8 Car position indicators
Audible and visible car position indicators shall be provided in elevator cars....
-
11B-411.4.8 Car position indicators
Audible and visible car position indicators shall be provided in elevator cars....
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side....
-
602.3 Electronic Support Documentation (Section-by-Section Analysis)
602.3 Electronic Support Documentation (Section-by-Section Analysis) This section proposes to require documentation in electronic formats—including Web-based self-service support and...
-
M305.3.3 Fittings
Standing supports shall not rotate within their fittings....
-
M305.3.3 Fittings
Standing supports shall not rotate within their fittings....
-
11B-407.4.10 Support rail
Support rails shall be provided on at least one wall of the car. Advisory 11B-407.4.10 Support rail....
-
11B-407.4.10 Support rail
Support rails shall be provided on at least one wall of the car. Advisory 11B-407.4.10 Support rail....
-
11B-407.4.10 Support rail
Support rails shall be provided on at least one wall of the car. Advisory 11B-407.4.10 Support rail....
-
11B-903.4 Back support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADAS] 903.4 Back Support. ...
-
11B-903.4 Back support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADAS] 903.4 Back Support....
-
11B-903.4 Back support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADA Standards] 903.4 Back Support....
-
M305.3.3 Fittings (Section-by-Section Analysis)
The MDE NPRM proposed to prohibit standing supports from rotating in their fittings. There were no comments on this section and it was not addressed by the MDE Advisory Committee....
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302 Description: Gripping surface hazards are sharp or abrasive elements that prevent an individual from sufficiently...
-
Midmark 630 HUMANFORM™ Procedures Table
Angle Range: 0 ̊ to 80 ̊ Foot Support Angle Range:0 ̊ to 90 ̊ 28" Upholstery Width Dimensions: Headrest: 12" (30.5 cm); Back support: 26.5" (67.3 cm); Seat: 28" (71.1 cm); Foot support...
-
602 Support Documentation
[See subsections ...]
-
603 Support Services
[See subsections ...]
-
602 Support Documentation
[See subsections ...]
-
603 Support Services
[See subsections ...]
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
Advisory Committee during its deliberations revealed that it is not always possible to transfer from adjoining sides at the end of the diagnostic equipment in the prone, supine, or side-lying position...
-
M301.3.2 Stirrups
Where stirrups are provided, they shall provide a method of supporting, positioning, and securing the patient’s legs....
-
Gripping Surface Cross Section and Clearances M301, M302, and M305.2
Gripping Surface Cross Section and Clearances M301, M302, and M305.2 Gripping surface for transfer supports shall be free of sharp or abrasive elements and shall have rounded edges per...
-
M305.3.2 Height (Section-by-Section Analysis)
There were no public comments on this requirement, and the MDE Advisory Committee supported the proposed technical provisions....
