Search Results "Patient in Prone Position"

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.5.1 Armrest Provision for Equipment Used by Patient in Seated Position

  5.5.1 Armrest Provision for Equipment Used by Patient in Seated Position. Armrests are not required but if provided cannot obstruct transfer supports....

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.8 Fittings

  Transfer supports shall not rotate within their fittings when in place for transfer.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.7 Clearance

  Clearance between the transfer support gripping surface and adjacent surfaces or obstructions shall be 1 ½ inches (38 mm) minimum.

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M305.2.7 Clearance (Section-by-Section Analysis)

  In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support. However, in the preamble to the MDE NPRM the Access Board...

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M305.2.3 Fittings

  Transfer supports shall not rotate within their fittings.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2.3.1 End Transfer Surface

  imaging equipment with bores shall be permitted to be 21 inches (535 mm) wide minimum but shall not be permitted to be less than the full width of the examination surface provided for the patient...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2.3.2 Side Transfer Surface

  imaging equipment with bores shall be permitted to be 21 inches (535 mm) wide minimum but shall not be permitted to be less than the full width of the examination surface provided for the patient...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2 Transfer Surface

  A transfer surface shall be provided and shall comply with M301.2.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2.3 Size

  The size of the transfer surface shall comply with M301.2.3.1 or M301.2.3.2. The size of transfer surfaces shall be measured from center points of their opposing sides.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.1 Transfer Surface Size

  5.2.1 Transfer Surface Size

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2 Transfer Surface Size Recommendations

  5.2 Transfer Surface Size Recommendations

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M301.2.2 Size

  The transfer surface shall be 30 inches (760 mm) wide minimum and 15 inches (381mm) deep minimum. Advisory M301.2.2 Size. The size requirements in this section apply only to the...

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M301.2 Transfer Surface

  A transfer surface shall be provided and shall comply with M301.2.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2.4 Unobstructed Transfer

  Each transfer surface shall provide two unobstructed sides for patient transfer. EXCEPTIONS: 1....

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.2.1 End Transfer Supports

  Transfer supports shall be positioned along 13 ½ inches (345 mm) minimum of the depth of the transfer surface....

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M302.3.2 Armrests

  Where diagnostic equipment is used by patients in a seated position, armrests shall be provided. Advisory M302.3.2 Armrests....

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.1 Location

  Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.4 Cross Section

  Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.3 Height

  During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.6 Gripping Surface

  Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M305.2.4 Cross Section (Section-by-Section Analysis)

  The proposed rule did not provide specific requirements for the cross section of transfer supports. However, in the MDE NPRM preamble, the Access Board noted that it was considering...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.3 Transfer Sides

  5.3 Transfer Sides.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.3 Transfer Sides Recommendations

  5.3 Transfer Sides Recommendations

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.2.2 Side Transfer Supports

  Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer surfaces....