For imaging equipment with transfer surfaces, the Committee recommends a transfer support be 28 inches minimum length and that a positioning support be 12 to 16 inches in length....
Search Results "Guy Support"
Filters
Commonly Searched Documents
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
-
vii. Ancillary equipment
Ancillary equipment includes items such as positioning straps or cushions; protective padding; adjustable, padded leg supports for gynecological examinations; and additional supports, rails...
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum....
-
Medical Diagnostic Equipment Accessibility Standards Sub-Committee Recommendations Weight Scales
Specifically, section M303, patient positions equipment designed to support seated in a wheelchair....
-
M305.3.2.2 Vertical Position
The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface....
-
"Doing work'' or "performing tasks.'' (Section-by-Section Analysis)
The Department agrees with this statement but cautions that unless the animal is individually trained to do something that qualifies as work or a task, the animal is a pet or support animal...
-
Doing "work'' or "performing tasks.'' (Section-by-Section Analysis)
The Department agrees with this statement but cautions that unless the animal is individually trained to do something that qualifies as work or a task, the animal is a pet or support animal...
-
Transfer Supports Location and Configuration M301.3 and M302.3
Transfer Supports Location and Configuration M301.3 and M302.3 Location of the transfer supports shall be a minimum of 6 inches to a maximum of 19 inches from the top of the transfer...
-
M301.3 Supports (Section-by-Section Analysis)
An editorial change was made to this section as a result of the change in M301.3.2, described below, to replace the word “stirrups” with the term “leg supports.”...
-
4.4.3 Backrest and Armrest
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device or supporting...
-
M301.3.3 Head and Back Support (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed to place the requirements for head and back support for diagnostic equipment used by patients in the supine, prone, or side-lying position in M301...
-
M305.5 Head and Back Support (Section-by-Section Analysis)
(Section-by-Section Analysis – M302.3.3), the technical requirements for head and back supports from M301 and M302 have been relocated to M305 Supports....
-
M305.3.1 Horizontal Position
Where the support is horizontal, the top of the gripping surface shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum above the standing surface....
-
M305 Supports
[See subsections ...]
-
M305 Supports
[See subsections ...]
-
EZ Dock EZ Launch® System for Kayaks and Canoes
with two heights for easy transfer from wheelchairs • Transfer slide boards with two heights for differing watercraft sizes • Railing system for slide board stabilization and transfer support...
-
F103 Modifications and Waivers
The Architectural Barriers Act authorizes the Administrator of the General Services Administration, the Secretary of the Department of Housing and Urban Development, the Secretary of...
-
5.4 Transfer Supports
5.4 Transfer Supports....
-
M305.2 Transfer Supports
Transfer supports shall comply with M305.2....
-
M305.2 Transfer Supports
Transfer supports shall comply with M305.2....
-
Tips for Assisting People Who Have Disabilities that are Not Apparent
Service and Emotional Support Animals Be aware that people who have disabilities that are not apparent may travel with emotional support animals or other service animals....
-
Locker Rooms
Locker Rooms Recommendations: Benches of the required size (24 inches deep and at least 48 inches long) can be integrated with lockers so that back support is provided from a wall....
-
2. Standing Supports
strength of standing supports....
