Requires the Premium User plan or above.
(Login or upgrade your account!)
Search Results "Work Surface"
Filters
Commonly Searched Documents
-
GE Profile™ Series 30" Slide-In Double Oven Electric Convection Range PS950EFES Model
-
GE® 24" Standard Clean Free-Standing Electric Range JAS02SNSS Model
Requires the Premium User plan or above. (Login or upgrade your account!) -
GE® 30" Slide-In Electric Convection Range JS750EFES Model
Requires the Premium User plan or above. (Login or upgrade your account!) -
GE Cafe™ Series 30" Free-Standing Gas Double Oven with Convection Range CGS990SETSS Model
Requires the Premium User plan or above. (Login or upgrade your account!) -
GE® 27" Drop-In Electric Range JM250DFBB Model
Requires the Premium User plan or above. (Login or upgrade your account!) -
GE® 24" Standard Clean Free-Standing Gas Range JGAS02SENSS Model
Requires the Premium User plan or above. (Login or upgrade your account!) -
Voting Areas
Floor surfaces must be stable, firm, and slip resistant....
-
2004 ADA and ABA Accessibility Guidelines
The following technical criteria in the proposed standards are based on the 2004 ADA and ABA Accessibility Guidelines: • Height of transfer surfaces on diagnostic equipment used by patients...
-
19 Inch Low Height
transfer surface....
-
4.34.6 KITCHENS
Accessible or adaptable kitchens and their components shall be on an accessible route and shall comply with the requirements of 4.34.6.
-
Pilot Rock N-20 Series Charcoal Grill
N Series grill cooking grates are fabricated using 5/8" dia. steel bars for support handles, and 1/2" dia. steel bars for the cooking surface. ...
-
M305.3.1.1 Horizontal Position
The length of gripping surfaces on horizontal standing supports shall be 4 inches (100 mm) minimum except for diagnostic equipment containing a wheelchair space which shall comply with M305.3.1.2...
-
M301.2.1 Adjustability (Section-by-Section Analysis)
The MDE NPRM proposed a transfer surface height range for diagnostic equipment used by patients in the supine, prone, or side-lying position of 17 inches minimum and 19 inches maximum....
-
Balco FMS-A and FMS-V Roll-Up Floor Mat
Dirt and moisture collect underneath the grate surface to keep floors clean and reduce maintenance. Rails can be replaced without dismantling the entire grid system....
-
M305.3.2.2 Vertical Position
The height of the lowest end of the gripping surface on vertical standing supports shall be 34 inches (865 mm) minimum and 37 inches (940 mm) maximum above the standing surface....
-
§ 38.23(c)(8) Handrails
them from outside the vehicle while starting to board, and to continue to use them throughout the boarding process, and shall have the top between 30 inches and 38 inches above the ramp surface...
-
1012.5 Slope
This section requires the slope of the surface of parking spaces and pull-up spaces to not be steeper than 1:48 in any direction....
-
Passenger Loading Zones [4.6.6]
A level surface (maximum 2% slope in any direction) for both the space and aisle is important for wheelchair transfer to and from vehicles and deployment of vehicle lifts or ramps....
-
1014.3 Floor
The floor within camp shelters shall comply with 1014.3.
-
R304.5.3 Cross Slope
R304.5.3 Cross Slope. The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum. At pedestrian street crossings without yield or stop control...
-
Addendum F: Relative Height Differences
Relative heights were calculated for high and low transfers for all three protocols. Refer to Addendum A for the definition of relative height. The following tables F1-F3 represent...
-
1014.3 Floor
The floor within camp shelters shall comply with 1014.3.
-
1.1.12 Ramp cross slope
1.1.12 Ramp cross slope. Measure for overall cross slope of ramps by establishing elevations at the extreme edges of the ramp at the top and bottom of the ramp and calculate the...
-
What is a good un-official "working" definition of "work surface"?
11B-805.7 goes on to list numerous items that would/could be included in the broad verbiage of "Built-in cabinets, counters and work surfaces"....
