The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
Search Results "Stable Surface"
Filters
Commonly Searched Documents
-
M301.2.2 Sunset
-
11B-805 Medical care and long-term care facilities
SECTION 11B-805 Medical care and long-term care facilities 11B-805.7 Built-in cabinets and work surfaces....
-
11B-1009.5.5 Surface
The surface of the transfer system shall not be sharp and shall have rounded edges....
-
11B-1009.4.4 Surface
Surfaces of transfer walls shall not be sharp and shall have rounded edges....
-
M301.2.3 Size (Section-by-Section Analysis)
As discussed in Section IV.B.1.c (Significant Changes – Transfer Surface Size), in the final rule the Access Board has revised this provision to account for the two types of transfer surfaces...
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements....
-
5.4.5.1 Transfer and Positioning Support Position for Imaging Equipment
The transfer or positioning support should be oriented horizontally on imaging equipment with transfer surfaces....
-
Figure 505.7.2 Handrail Non-Circular Cross Section – Drawing from the U.S. Access Board
-
M301.2.3 Size
The size of the transfer surface shall comply with M301.2.3.1 or M301.2.3.2. The size of transfer surfaces shall be measured from center points of their opposing sides....
-
M301.3.1 Transfer Supports
A.1) A transfer support will extend horizontally along the side of the patient scanning/imaging table at least the minimum width of the transfer surface, but in all cases a 28 inches minimum...
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48.
-
4.7.9.1 General
Where utility sinks are provided in a recreation facility that also contains a cook top or conventional range, at least 5 percent, but not less than one in each accessible space,...
-
1991 / 1994 ADA Standards - Plan Review Tool - Slopes
1991 / 1994 ADA Standards - Plan Review Tool - Slopes Click here to view/download the pdf "1991 / 1994 ADA Standards - Plan Review Tool - Slopes" (354 KB) * * * * * * *
-
M303.3.3.2 Cross Slope
The cross slope of ramp runs shall not be steeper than 1:48.
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
Adjustable Height Range Considered
to make up the difference between the two surfaces, in one direction or the other....
-
5.3.2 Transfer Sides Recommendations for M301
the long side of the surface....
-
302 Floor or Ground Surfaces
Section 302 requires floor or ground surfaces to be stable, firm, and slip resistant and provides specifications for carpets and surface openings. Comment....
-
Arriving at the Polling Place: Parking
Accessible parking spaces and the access aisles serving them must be on a surface that is stable, firm, and slip resistant (e.g., clear of gravel or mud) without wide cracks or broken pavement...
-
1. Standing Supports
The proposed rule included a provision requiring standing supports on each side of the standing surface and compliance with the technical requirements for standing supports in proposed M305.3...
-
5.4.2.1 Transfer Support Length for Stretchers
5.4.2.1 Transfer Support Length for Stretchers. Transfer supports on stretchers should be a minimum of 15 inches long.
-
Visual Detection of Detectable Warning Materials by Pedestrians with Visual Impairments - Final Report
(Task Order 18 under Project DTFH61-01-C-00049) Authors: James Jenness & Jeremiah Singer May 24, 2006 Prepared for: Federal Highway Administration Washington,...
