[2010 ADA Standards] 407.4.7.1.1 Type. Control buttons shall be identified by tactile Characters complying with 703.2....
Search Results "Industry Standard"
Filters
Commonly Searched Documents
-
11B-407.4.7.1.1 Type
-
The Accessibility Management Platform (AMP)
Accessibility Management Platform (AMP) provides the infrastructure to facilitate all aspects of a successful digital accessibility compliance program and conform to leading accessibility standards...
-
Sec. 469.052(b)
(b) The standards and specifications adopted by the commission under this chapter must be consistent in effect with the standards and specifications adopted by the American National Standards...
-
Applying Accessibility Guidelines to Your Site
How did we end up with so many accessibility guidelines and standards? Which guidelines and standards apply to your site?...
-
§ 36.606(d)
(d) When the standards of the Act against which a code is deemed equivalent are substantially revised or amended, a certification of equivalency issued under the preexisting standards is...
-
§ 36.606(d)
(d) When the standards of the Act against which a code is deemed equivalent are revised or amended substantially, a certification of equivalency issued under the preexisting standards is...
-
SAFE HARBOR
If an element never complied with the 1991 ADA Standards then there is no safe harbor for that element....
-
Breast Platform [M303.4.1]
According to industry, equipment currently manufactured ranges anywhere between 25 and 28 inches for the lowest measurement of the breast platform....
-
11B-410.7 Landing size
ETA Editor's Note There are no requirements for landing size in 2010 ADA Standards, although the door maneuvering clearance requirements at 404.2.4 should be applicable outside the platform...
-
ADA Safe Harbor Provisions
required by the 2010 Standards....
-
Reduced scoping for play areas and other recreation facilities. (Section-by-Section Analysis)
The Department has been persuaded that the ADA's approach to barrier removal, the readily achievable standard, provides the appropriate balance for the application of the 2010 Standards...
-
Declaration of Conformity
A few commenters from the telecommunications industry and disability organizations urged the Board to adopt the Declaration of Conformity as recommended by the TAAC....
-
Operable Parts of Windows
Comment from industry opposed such a requirement....
-
Automated Revolving Doors
While manufacturers have developed safety criteria, the industry safety code for automated doors referenced by ADAAG does not currently address revolving doors, and certain questions remain...
-
2.1.3. Baseline
The baseline represents the Department’s best assessment of the state of the movie exhibition industry. ...
-
4.2.8. Zero Growth After Five Years
The movie industry has undergone significant changes in recent years as a result of the digital conversion, which has had an impact on the number of auditoriums opening and closing. ...
-
1.1 Basis.
This AC is based on federal regulations and standards....
-
Thresholds at Doorways
The 1991 Standards, at section 4.13.8, require the height of thresholds at doorways not to exceed ½ inch and thresholds at exterior sliding doors not to exceed ¾ inch....
-
§ 36.211(c)
(c) If the proposed standards reduce the number of required accessible elements below the number required by the 1991 Standards, the number of accessible elements in a facility subject to...
-
§ 35.133(c)
(c) If the proposed standards reduce the number of required accessible elements below the number required by the 1991 Standards, the number of accessible elements in a facility subject to...
-
18(b)
(D) the required number of accessible rooms for individuals who are deaf or hard of hearing as set forth in ADA Standards §§ 9.1.2 and 9.1.3, that comply with ADA Standards § 9.3....
-
18(a)
(iii) The plans comply with the ADA Standards....
-
BTX Intelligent Fashion Motorized Roller Shades
The BTX Intelligent Fashion Roller Shade program combines some of the most advanced motorization technology in the industry with a broad collection of designer textiles for both contemporary...
-
New Construction and Alterations
The 2010 Standards lay out accessibility design requirements for newly constructed and altered public accommodations and commercial facilities....
