Standard Features Adjustment range 24” - 50“ Front surface adjustment range 20” - 57” (4” below, 7” above rear surface), with 15 +/- tilt Power adjusted standard 110V, UL Listed...
Search Results "Parking Surface"
-
Populas Vox Two-Story Adjustable Dual Surface Workstation
-
4.1.2(17)
(17) If fixed or built-in seating, tables, or work surfaces are provided in accessible spaces, at least 5 percent, but always at least one, of seating spaces, tables, or work surfaces shall...
-
(4) Adjustability: Method of Measurement
The MDE NPRM proposed that the measurement of the height of the transfer surface for both diagnostic equipment used in the supine, prone, or side-lying position and diagnostic equipment...
-
Alterations
In alterations, the minimum number is based on the total number of spaces altered or added to a lot. Recommendation: Where a lot is not fully altered, it is recommended that the...
-
SuperDeck Beach Boardwalk
SuperDeck's low-maintenance decking provides a firm, secure beach boardwalk surface over virtually any terrain....
-
Figure 505.6 Horizontal Projections Below Gripping Surface – Drawing from the U.S. Access Board
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel....
-
Built-up Curb Ramps [4.7.6]
Built-up curb ramps are permitted where they do not project into vehicular traffic lanes or access aisles at parking spaces and passenger loading zones....
-
Seat Width Evaluation
many participants (the 25th through 95th percentiles) for their level, highest and lowest height transfer regardless of the presence or absence of grab bars or a backrest on the transfer surfaces...
-
7.2.2.1 Determining Impracticability
The surface is not firm and stable for a distance of 45 feet or more (14 m). Limiting Factor 3. ...
-
Inpro Corporation JointMaster® 316 Series Single Sightline for Carpet Floor Expansion Joint Covers
The 316 series system was specially designed for continuous flooring types such as carpet and vinyl sheet. Features & Benefits System reduces joint widths of up to 4"...
-
AccessRec GrassProtecta Slip Resistant Grass Reinforcement Mesh
prone to wear, rutting and smearing which can result in a muddy surfaces incapable of withstanding vehicular or pedestrian applications....
-
Light Rail Platform Slope
The Board has explicitly specified that rail platforms shall slope no more than 1:48 in any direction, consistent with cross slope provisions for walking surfaces in section 403....
-
Executive Summary
After traveling over each surface, subjects were asked to subjectively rate each surface and decide whether the surface was acceptable or not....
-
Signage [4.6.4]
Accessible spaces must be designated by the access symbol, which can be mounted on walls, posts, or from garage ceilings so that it is not obscured by vehicles parked in the space....
-
Ytterberg Scientific Inc. FloorPro® Floor Flatness Measurement Device
It's Easier to Use, Gets Faster Results, and Produces Superior Reporting on More ASTM Specifications. FloorPro® Gives You Immediate Results, Instant F-Numbers, Waviness Index,...
-
Impact Recovery Systems Slow Stop Rebounding Bollard Video Presentation
A video of the SlowStop Rebounding Bollard Presentation.
-
Impact Recovery Systems Slow Stop Rebounding Bollard - How Does It Work
This is a Computer simulation of a SlowStop Bollard reacting to an impacting object. This video shows a cut-away view of the internal workings.
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible. ...
-
Access Board: Accessible Route Carpet
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
Non-Circular Cross Sections: ADA Standard Section 505.7.2
Section 505.7.2 covers the current ADA Standards for the non-circular cross section of handrail gripping surfaces.
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
