No public comments were submitted on this issue, but the MDE Advisory Committee voiced concern about surface hazards stating, “gripping surface configurations must provide an effective and...
Search Results "Kitchen Work Surface"
Commonly Searched Documents
-
M305.2.5 Surface Hazards (Section-by-Section Analysis)
-
1017.6 Openings
Openings in the surface of trails, passing spaces, and resting intervals shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1017.6 Openings. ...
-
1017.6 Openings
This section requires openings in the surface of trails, passing spaces, and resting intervals such as spaces between the boards in a boardwalk to not allow passage of a sphere more than...
-
1017.6 Openings
Openings in the surface of trails, passing spaces, and resting intervals shall not allow the passage of a sphere more than 1/2 inch (13 mm) in diameter. Advisory 1017.6 Openings....
-
5.1.1 Transfer Surface Height Adjustability
5.1.1 Transfer Surface Height Adjustability. The transfer surface should have an adjustable height in small virtually continuous increments....
-
5.1.2 Transfer Surface High Height
5.1.2 Transfer Surface High Height. The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches....
-
Circulation Paths Serving Exempted Spaces [§203]
Circulation Paths Serving Exempted Spaces [§203] Portions of common use circulation paths serving exempt spaces within a work area are not required to comply, including routes to...
-
Resting Intervals on Trails
This is because working against the sideways pull of the cross slope can double the effort needed to make forward progress....
-
National Network of ADA Centers
The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum measured from the floor to the top of the transfer surface....
-
11B-813.2.1.2 Clearance
Floor or ground surfaces of clearances shall comply with Section 11B-302. Changes in level are not permitted....
- Filter Pave™ Porous Paving for Stormwater Management
-
5.1 Transfer Surface Height
5.1 Transfer Surface Height...
-
810.5.1 Slope
810.5.1 Slope. Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing...
-
810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
11B-810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. Exception: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. EXCEPTION: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...
-
R407.6.1 Slope
R407.6.1 Slope. Landing slopes shall be 2 percent maximum in any direction.
-
R407.3 Cross Slope
R407.3 Cross Slope. The cross slope of ramp runs shall be 2 percent maximum.
-
Wayfinding is more than just graphics (slides 2 – 4)
Cognitive process (slides 2 - 4). [Wayfinding is] really more of a cognitive process. You gather information at the beginning. You cite and execute a path to take. And then you...
-
A. Slope at Door
A. If a fully automatic door is not provided, is the walkway in front of the lobby door level, without any portion steeper than 1:50 (critical dimension of ´" or less), so persons...
-
A4.13.9 Door Hardware
Some disabled persons must push against a door with their chair or walker to open it. Applied kickplates on doors with closers can reduce required maintenance by withstanding abuse...
-
A4.13.9 DOOR HARDWARE
Some disabled persons must push against a door with their chair or walker to open it. Applied kickplates on doors with closers can reduce required maintenance by withstanding abuse...
-
APPENDIX C
APPENDIX C On‐Site Inspection Form ETA Editor's Note Click here to download the pdf version of the document with the ON-SITE INSPECTION FORM in APPENDIX C, pdf page 41.
-
11B-810.5.1 Slope
Rail platforms shall not exceed a slope of 1:48 in all directions. Exception: Where platforms serve vehicles operating on existing track or track laid in existing roadway, the...