1. Grab bar reinforcement complying with Sections 11B-809.10.5.2, 11B-809.10.6.4, or 11B-809.10.7.3. 2. Interior door opening width complying with Section 11B-404.3.1. 3....
Search Results "Ground Floor"
-
11B-233.3.1.2.6.5 Additional requirements.
-
4.34.5.1 DOORS
Doors shall not swing into the clear floor space required for any fixture....
-
Fixtures
Fixtures TAS 604.3.2 also allows the clear floor space and clearances required at other “fixtures” to overlap the water closet clearance....
-
Station platforms
Station platforms must be coordinated with the vehicle floor height. (DOT ADA Standard 810.5.3.)...
-
F231.3 Holding Cells
Where provided, central holding cells and court-floor holding cells shall comply with F231.3....
-
231.3 Holding Cells
Where provided, central holding cells and court-floor holding cells shall comply with 231.3....
-
§ 38.107(a)(1)
(1) The minimum clear floor area shall be 35 inches by 60 inches....
-
11B-231.3 Holding cells
Where provided, central holding cells and court-floor holding cells shall comply with Section 11B-231.3. ...
-
11B-231.3 Holding cells
Where provided, central holding cells and court-floor holding cells shall comply with Section 11B-231.3....
-
11B-231.3 Holding cells
Where provided, central holding cells and court-floor holding cells shall comply with Section 11B-231.3....
-
1. Accessible toilet
Accessible toilet with rear and side grab bars, clear floor space for wheelchair transfer, and an accessible flush valve....
-
231.3 Holding Cells
Where provided, central holding cells and court-floor holding cells shall comply with 231.3....
-
Location: ADA Standard Section 703.4.2
Signs containing tactile characters shall be located so that a clear floor space of 18 inches (455 mm) minimum by 18 inches (455 mm) minimum, centered on the tactile characters, is provided...
-
Side Approach
Side Approach The maximum reach depth for a high (54 inch maximum) reach is 10 inches, measured from the clear floor space....
-
McGuire Manufacturing Co., Inc. 1151AWC: Offset with 151 Stainless Steel Basket Strainer
Offset sink strainer with stainless steel basket strainer with stainless steel basket. 2 3/4" x 4 3/8" OD.
-
Just Manufacturing Stainless Steel Cup Strainer ADA Compliant Drain System
Body of stainless steel. Strainer of stainless steel. Stopper of rubber. 17 gauge chrome plated brass tailpiece. Die-cast zinc lock...
-
McGuire Manufacturing Co., Inc. 155LATWC: Offset Lift and Turn PO Plug
Wheelchair lavatory strainer. Furnished with heavy brass elbow and 17GA seamless brass offset tailpiece. 8 3/4" x 5 1/8" OD.
-
R&D Workshop Trim-A-Slab Expansion Joint Repair
Trim-A-Slab is a replacement for rotted and old wood typically found between slabs in driveways and sidewalks. This wood was used during the slab construction, and is part of the...
-
NanoPave® JSS 2-in-1 Joint Stabilizer and Sealer
NanoPave JSS (NP-JSS) is a revolutionary 2-in-1 joint stabilizer and sealer product for use with pavers, natural stone, and flagstone. NP-JSS creates a strong, durable bond in common...
-
Stabilizer Solutions StaLok Stabilizer Joint Sand
STABILIZED JOINT SAND THAT STAYS PUT BETWEEN PAVERS StaLok Paver Sand sets up strong and locks in between pavers. It allows water to drain and ‘heals’ itself. The sand repairs...
-
GAP ARMOUR
GAP ARMOUR IS AN INNOVATIVE RUBBER MATERIAL ...that easily installs (with a rubber hammer) into open concrete expansion joints to completely seal and protect! Gap Armour can be...
-
Avoid the extremes of surface reflectivity and contrast (slides 11 and 13)
Somebody asked yesterday about polarizing film for flooring. We can do that with matte texturing....
-
Car Designations: ADA Standard Section 407.2.3.2
Section 407.2.3.2 covers the current ADA Standards for elevator car designations.
