(2) Ramp surface....
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
§ 38.95(c)(2) Ramp surface
-
BORA Classic Cooktop Extraction System Installation Video
BORA Classic Cooktop Extraction System Installation Video
-
Engineered Wood Fiber
In addition, there were five sites surfaced with a combination PIP and EWF, and eight sites surfaced with a combination TIL and EWF. ...
-
9.a [§ 4.7.5]
To answer this question you need to determine the slope of the flared sides to make sure it is 10 percent or less....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
1008.2.5.3.1 Handrail Gripping Surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
Play Areas
Word Fillable Form (0.4MB) Word Non-Fillable Form (0.3MB) PDF Non-Fillable Form (0.3MB)
-
406.5 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
Tile Tech Pavers® Porcelain Pavers™ Series
technical and aesthetic properties, our porcelain pavers range can meet a number of important safety requirements for exterior floor coverings in public places, combining an anti-slip surface...
-
M304.2.1 Slip Resistant
The surface on which the patient stands shall be slip resistant....
-
406.5 Location
Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular traffic lanes, parking spaces, or parking access aisles....
-
1014.1 General
The technical requirements address the entrance to camp shelters (1014.2), including transfer access (1014.2.1) and roll-in access (1014.2.2); and the floor within camp shelters (1014.3)...
-
Shower Stalls [4.21]
ADAAG provides specifications for several types of shower stall designs: roll-in, transfer, and, in hotels (section 9), a combination of the two....
-
Lift Compatibility (M301.4 and M302.4)
A patient lift may be the only means of providing access to certain equipment that cannot meet the technical criteria for transfer surface height (see M301.2.1 and M302.2.1) because of the...
-
Impact Annenuation [sic]
Surface Impact Testing Results per ASTM F 1292: Phase I surfaces (unaged) and Phase II (exposed for 6 months) Surface/ Test Drop 2 G Drop3G Drop2...
-
Figure 1009.4.5 Grab Bars for Transfer Walls – Drawing from the U.S. Access Board
-
Tread Obstacles on Trails
A tread obstacle is anything that interrupts the evenness of the tread surface. On trails, tread obstacles often occur as a result of ruts, roots, and rocks in the tread surface....
-
11B-1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951. Ground surfaces shall be inspected and maintained regularly and frequently to ensure continued compliance with ASTM F 1951....
-
Circular Cross Section: ADA Standard Section 505.7.1
Section 505.7.1 covers the current ADA Standards for the circular cross section of handrail gripping surfaces.
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Use Zones: ADA Standard Section 1008.2.6.2
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see “Referenced Standards” in Chapter 1)....
-
Accessible - Changes in Level
Accessible - Changes in Level: Changes in level up to 1/4" may be vertical and without edge treatment. Changes in level between 1/4" and 1/2" shall be beveled with a slope no...
-
General: ADA Standard Section 240.1
Section 240.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for play areas.
-
1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
