Commercial vans used for accessible transit may be taller than passenger vans.◼...
Search Results "Transit Sign"
Commonly Searched Documents
-
11B-503.5 Vertical clearance
-
11B-503.5 Vertical clearance
Commercial vans used for accessible transit may be taller than passenger vans. ◼...
-
Cross Slope (R302.6) (Section-by-Section Analysis)
Pedestrian street crossings without yield or stop control are crossings where there is no yield or stop sign, or where there is a traffic signal that is designed for the green phase....
-
708.2 Audible and Visual Indicators
Signs indicating the meaning of visual signals should be provided....
-
708.2 Audible and Visual Indicators
Signs indicating the meaning of visual signals should be provided....
-
Each bank of public telephones must have one or more wheelchair accessible telephones and these and other public telephones must have the ability to amplify the volume at the handset.
A sign must identify telephones equipped with amplification....
-
At least one public TDD must be provided.
Signs must identify the location of the TDD and provide direction from other telephone banks....
-
7.4.8 Protruding Objects
Constructed features, including signs, shall not extend into the trail tread more than 4 inches (100 mm) between 27 inches (685 mm) and 80 inches (2030 mm) above the surface of the trail...
-
SUPPLEMENTARY INFORMATION:
Passenger railroads that choose not to provide level-entry boarding at new or altered station platforms must get concurrence from the Federal Transit Administration (FTA) or Federal Railroad...
-
T402 Ramps and Bridgeplates
bridgeplates in the 2016 Non-Rail Vehicle Guidelines include provisions on design load, installation and operation, emergency operation, surfaces, clear width, edge guards, running slope, transitions...
-
Section 37.155 Factors in Decision To Grant an Undue Financial Burden Waiver
increases in fares, resources available to implement complementary paratransit over the period of the plan, current level of accessible service (fixed route and paratransit), cooperation among transit...
- Takeform Fusion Signage Interior Stairwell Type N
- Texas Department of Transportation (TxDOT) Computer Aided Drawings Standard Plan Files
-
1011.4, Item 3
required to comply with Section 1011.1, and that leads directly to a grade-level exterior exit by means of an exit enclosure or an exit passageway shall be identified by a tactile exit sign...
-
4.30.5* Finish and Contrast
The characters and background of signs shall be eggshell, matte, or other non-glare finish....
-
1013.4, Item 3
required to comply with Section 1013.1, and that leads directly to a grade-level exterior exit by means of an exit enclosure or an exit passageway shall be identified by a tactile exit sign...
-
Feature 3 - Building Entrance
Feature 3 - Building Entrance Signs for an alternate accessible entrance are posted at inaccessible entrances and key decision points along the accessible route....
-
11B-216.7 Elevators
to provide specific elevators for public use that comply with these building standards shall have the location of and the directions to these elevators posted in the building lobby on a sign...
-
Accommodations for Passengers Who are Deaf or Hard of Hearing
[Sec. 382.47(b)] More specifically, carriers must implement this requirement by using open captioning or an inset for a sign language interpreter as part of the video presentation....
-
Finish and Contrast [4.30.5]
Finish and Contrast [4.30.5] All signs covered by 4.30 must have a non-glare finish, such as matte or eggshell. Recommendations: An eggshell finish is recommended....
-
Typical Issues
If the accessible entrance is not the main entrance to the polling place, then signs must be located at inaccessible entrances to the polling place to direct voters to the accessible entrance...
-
11B-216.7 Elevators
to provide specific elevators for public use that comply with these building standards shall have the location of and the directions to these elevators posted in the building lobby on a sign...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...