One means of entry/exit must be a fixed pool lift or sloped entry; the other entry can be a transfer wall, transfer system, or pool stairs....
Search Results "Transfer Surface"
-
2. What does the ADA require for accessibility of pools?
-
Populas Vox Two-Story Adjustable Dual Surface Workstation
Standard Features Adjustment range 24” - 50“ Front surface adjustment range 20” - 57” (4” below, 7” above rear surface), with 15 +/- tilt Power adjusted standard 110V, UL Listed...
-
Location and Size
The transfer support would be located on the side of the transfer surface that is opposite the transfer side (see M301.2.3 and M302.2.3) similar to the provisions in the 2004 ADA and ABA...
-
4.1.2(17)
(17) If fixed or built-in seating, tables, or work surfaces are provided in accessible spaces, at least 5 percent, but always at least one, of seating spaces, tables, or work surfaces shall...
-
SuperDeck Beach Boardwalk
SuperDeck's low-maintenance decking provides a firm, secure beach boardwalk surface over virtually any terrain....
-
Figure 505.6 Horizontal Projections Below Gripping Surface – Drawing from the U.S. Access Board
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel. Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
11B-405.3 Cross slope
Cross slope is the slope of the surface perpendicular to the direction of travel....
-
Needs Photos or Technical Info
This article is a good start but, really could use some photos to illustrate the text. For example, what is a faucet that is placed out of reach for persons with cognitive...
-
Kompan, Inc. M582 - PlayWorks Sand Play Structure
Three platform levels offer differing elevations at appropriate transfer heights, enabling everyone to take part in play....
-
7.2.2.1 Determining Impracticability
The surface is not firm and stable for a distance of 45 feet or more (14 m). Limiting Factor 3. ...
-
Inpro Corporation JointMaster® 316 Series Single Sightline for Carpet Floor Expansion Joint Covers
The 316 series system was specially designed for continuous flooring types such as carpet and vinyl sheet. Features & Benefits System reduces joint widths of up to 4"...
-
Light Rail Platform Slope
The Board has explicitly specified that rail platforms shall slope no more than 1:48 in any direction, consistent with cross slope provisions for walking surfaces in section 403....
-
11B-608.5.1 Reserved
[2010 ADAS] 608.5.1 Transfer Type Shower Compartments....
-
4.16.2 Clear Floor Space
However, in accommodating assisted transfers, these guidelines were less of an issue than providing space adjacent to the water closet for caregivers and including a 5’ turning radius in...
-
Ytterberg Scientific Inc. FloorPro® Floor Flatness Measurement Device
It's Easier to Use, Gets Faster Results, and Produces Superior Reporting on More ASTM Specifications. FloorPro® Gives You Immediate Results, Instant F-Numbers, Waviness Index,...
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible. ...
-
Access Board: Accessible Route Carpet
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
Section 37.165 Lift and Securement Use
Under this rule, it is no longer permissible to require such a transfer....
-
Non-Circular Cross Sections: ADA Standard Section 505.7.2
Section 505.7.2 covers the current ADA Standards for the non-circular cross section of handrail gripping surfaces.
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
