Search Results "Grab Bar Height"

• Research and History > Research Documents > The Impact of Transfer Setup on the Performance of Independent Transfers: Phase I Final Report
  Evaluation of transfers

  There was a high frequency of lateral grab bar use and front grab bar/lateral grab bar together upon initial hand placement....

• Federal Documents > Standards > 2010 ADA Standards
  Dispensers: ADA Standard Section 604.7

  Section 604.7 covers the current ADA Standards for toilet paper dispensers.

• Federal Documents > Technical Assistance > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment - Example Applications of Proposed Standards
  Figure M1: Overview of M301 Diagnostic Equipment for Use by a Patient in a Supine, Prone, or Side-Lying Position

  [See subsections ...]

• Federal Documents > Standards > Uniform Federal Accessibility Standards (UFAS)
  A4.27.3 HEIGHT

  A6 further illustrates mandatory and advisory control mounting height provision for typical equipment....

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.3.2 Height

  The height of gripping surfaces for standing supports shall be based on the position of the standing supports in relation to the standing surfaces they serve....

• Research and History > Research Documents > Independent Wheelchair Transfers in the Built Environment: How Transfer Setup Impacts Performance Phase 2: Final Report
  Protocol A Heights Obtained

  The transfer heights obtained in protocol A for both sample groups can be seen in tables E4 and E5. Table E4....

• State and Local Documents > Codes and Standards > 2013 California Standards for Accessible Design Pocket Guide
  406.4.1 Clear height

  406.4.1 Clear height.  The clear height of each floor level in vehicle and pedestrian traffic areas shall be not less than 7 feet (2134 mm). Advisory 406.4.1 Clear height.  ...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.4 Leg Supports

  Leg supports shall provide a method of supporting, positioning, and securing the patient’s legs.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2 Transfer Surface

  A transfer surface shall be provided and shall comply with M301.2.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.1 General

  Diagnostic equipment that supports patients in a supine, prone, or side-lying position shall comply with M301.  EXCEPTION: Examination chairs complying with M302 that recline to...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M301.2.3 Size

  The size of the transfer surface shall comply with M301.2.3.1 or M301.2.3.2. The size of transfer surfaces shall be measured from center points of their opposing sides.

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M301.2.3 Size (Section-by-Section Analysis)

  The MDE NPRM proposed a transfer surface size for diagnostic equipment used in the supine, prone, or side-lying position of 30 inches wide and 15 inches deep minimum. (proposed...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.1 Transfer Surface Size Recommendations for M301

  5.2.1 Transfer Surface Size Recommendations for M301 Description: The transfer surface is the part of the diagnostic equipment onto which patients who use mobility devices or aids...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.1.1 Transfer Surface Width

  5.2.1.1 Transfer Surface Width. The transfer surface should be 28 inches wide minimum for equipment used by patients in a supine, side-lying, or prone position.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2 Transfer Surface Size for Equipment Used by Patients in Supine, Prone, or Side-Lying Position

  5.2 Transfer Surface Size for Equipment Used by Patients in Supine, Prone, or Side-Lying Position.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.1 Transfer Surface Size

  5.2.1 Transfer Surface Size

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2.1.2 Transfer Surface Depth

  5.2.1.2 Transfer Surface Depth. The transfer surface should be 17 inches deep minimum for all equipment used by patients in a supine, side-lying, or prone position with the exception...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.2 Transfer Surface Size Recommendations

  5.2 Transfer Surface Size Recommendations

• State and Local Documents > State Technical Assistance > California Department of Managed Health Care - Physical Access to Health Care Fact Sheet
  Examples of access:

  Exam table that lowers to 17-19 inches from the floor Many people find these tables easier to use. There are many ways to help people get access. See the [images]...

• Federal Documents > Technical Assistance > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment - Example Applications of Proposed Standards
  M301.4.1 Clearance in Base

  [See subsections ...]

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M301.2.2 Size

  The transfer surface shall be 30 inches (760 mm) wide minimum and 15 inches (381mm) deep minimum. Advisory M301.2.2 Size. The size requirements in this section apply only to the...

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M301.2 Transfer Surface

  A transfer surface shall be provided and shall comply with M301.2.