Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
Search Results "Coin Slot Height"
Filters
Commonly Searched Documents
-
703.5.8 Character Spacing
-
R405.3.4 Clearance Reduction
Between 230 mm (9 in) and 685 mm (2.25 ft) above the finish surface, the knee clearance shall be permitted to reduce at a rate of 25 mm (1 in) in depth for each 150 mm (6 in) in height....
-
Do drinking fountains pose hazards as protruding objects?
Cantilevered units at standard heights for people who stand must be recessed or protected as protruding objects....
-
Character Specifications
For characters with rectangular cross sections, a stroke thickness of 10% to 15% of the character height was specified (based on the uppercase "I")....
-
Doors in a Series
The height of door and gate hardware (34 to 48 inches) is specified in section 404.2.7....
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
Introduction
Footrest clearance height and depth...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
11B-703.5.8 Character spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
203.6 Single Occupant Structures
Single occupant structures accessed only by passageways below grade or elevated above standard curb height, including but not limited to, toll booths that are accessed only by underground...
-
4. Shower Wand
Is there an adjustable height hand-held shower wand with at least a 60" long hose provided so persons who bathe from a seated position may wash and rinse with the directional spray?...
-
2. Using the Tape Measure
Using the Tape Measure A metal tape measure is needed to measure the length, width, height, and depth of various elements....
-
502.2.1 On-street parallel parking
Curbs adjacent to such spaces must be of a height that does not interfere with the opening and closing of motor vehicle doors. Figure 502.2 Vehicle Parking Spaces...
-
Food and Beverage Service
Accommodating Diners with Disabilities factsheet provides both legal standards and promising practices for paths of travel, approach to dining spaces, seating, dining table and service counter heights...
-
[A] PUBLIC WAY
of land open to the outside air leading to a street, that has been deeded, dedicated or otherwise permanently appropriated to the public for public use and which has a clear width and height...
-
PUBLIC WAY
of land open to the outside air leading to a street, that has been deeded, dedicated or otherwise permanently appropriated to the public for public use and which has a clear width and height...
-
ASI Global Partitions Phenolic Color-Thru
Slotted keeper coupled with gravity hinges allows access in an emergency. Vault Hinge Rugged, attractive wrap-around hinge. Extra strong for heavy-duty installations....
-
§ 36.402(b)(1)
rehabilitation, reconstruction, historic restoration, changes or rearrangement in structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height...
-
Chapter 3: Building Blocks
Substantive revisions made in the final rule include: lowering the maximum height for side reaches from 54 to 48 inches (308.3.1) providing a limited exception from this...
-
1017.5 Tread Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
CalCasp Training: Advanced Scoping
This course will provide a series of scenarios and/or situations that are complex and not as easy as looking up the height of a grab bar in the code book....
-
11B-411.2.1.3.2 Touch screen call console arrangement
The accessibility function button shall be located at a height of 36 inches (914 mm) to 42 inches (1067 mm) above the finish floor....
