Dining surfaces include, but are not limited to, bars, tables, lunch counters, and booths....
Search Results "Vertical Grab Bar"
Filters
Commonly Searched Documents
-
General: ADA Standard Section 902.1
-
11B-411.2.1.3.4 Position
Keypads or buttons shall slope away from the user at 15 to 25 degrees from the vertical plane....
-
11B-411.2.1.3.4 Position
Keypads or buttons shall slope away from the user at 15 to 25 degrees from the vertical plane....
-
Door and Gate Surfaces: ADA Standard Section 404.2.10
Section 404.2.10 covers the current ADA Standards for door and gate surfaces on manual doors and gates.
-
11B-410.8 Restriction sign
For lifts with a signed installation contract before May 1, 2008: CCR, Title 8, Section 3094 provides safety regulations for Vertical Platform (Wheelchair) Lifts....
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
Pilot Rock FSW-30 Campfire Ring
This flange provides extra strength against heat warpage and eliminates a vertical edge. Draft holes are provided for fire ventilation....
-
§ 37.42(f)
boarding means a boarding platform design in which the horizontal gap between a car at rest and the platform is no more than 10 inches on tangent track and 13 inches on curves and the vertical...
-
§ 37.42(f)
boarding means a boarding platform design in which the horizontal gap between a car at rest and the platform is no more than 10 inches on tangent track and 13 inches on curves and the vertical...
-
Thresholds: ADA Standard Section 608.7
Section 608.7 covers the current ADA Standards for thresholds in shower compartments.
-
11B-608.7 Thresholds
In transfer type shower compartments, thresholds ½ inch (12.7 mm) high maximum shall be beveled, rounded, or vertical....
-
Brewer Access™ High-Low Exam Table 700
Brewer's Access High-Low Exam Table design provides an 18" profile in the seated position to allow level transfer from standard wheelchair heights, complete with upright seat back and safety grab...
-
11B-307.4.1 Guy braces
Where a guy support is used within either the width of a circulation path or 24 inches maximum outside of a circulation path, a vertical guy brace, sidewalk guy or similar device shall be...
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
Allegion Falcon XX Series Cross Bar Exit Devices
For high use areas that demand high-performing products, the Falcon XX Series fills the bill with a sleek, tough and attractive exit device that delivers ANSI Grade 1 performance....
-
Beveled: ADA Standard Section 303.3
Section 303.3 covers the current ADA Standards for beveled level changes.
-
General: ADA Standard Section 306.1
Section 306.1 of the ADA Standards covers information in the current ADA Standards for knee and toe clearance.
-
Visible Signals: ADA Standard Section 407.2.2.2
Section 407.2.2.2 covers the current ADA Standards for elevator visible signals.
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
11B-902.1 General
Dining surfaces include, but are not limited to, bars, tables, lunch counters, and booths....
-
11B-411.2.1.3.4 Position
The face of individual elements or group of individual elements that are operated by user input shall slope away from the user at 15 to 25 degrees from the vertical plane. ...
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
