At elevator landings. Within areas of refuge....
Search Results "Operation (Elevator)"
-
1009.10 Directional signage
-
402.3.1 Private Listening (Section-by-Section Analysis)
Section-by-Section Analysis) This section proposes to require that, where ICT subject to 402.3 provides a mechanism for private listening—such as a handset or headphone jack—it must have a mode of operation...
-
BEA Inc. Keyswitches Access Control Devices
single wall plates or double gang combo plate • Available with momentary or maintained contact • Capable of switching 6A @ 125 VAC or 3A @ 250 VAC • Combo plate allows for independent operation...
-
907.5.2.3 Visible alarms
Visible alarm notification appliances shall not be required in elevator cars....
-
[F] 907.5.2.3 Visible alarms
Visible alarm notification appliances shall not be required in elevator cars....
-
407.4.7.1.3 Symbols
Table 407.4.7.1.3 Elevator Control Button Identification Control Button Tactile Symbol Braille Message Emergency Stop "ST"OP Three...
-
§ 37.209 Training and other requirements
OTRB operators shall comply with the requirements of §§37.161, 37.165-37.167, and 37.173....
-
11B-407.4.7.1 Buttons
Car control buttons shall comply with Section 11B-407.4.7.1.
-
11B-407.4.6.2.3 Illumination
Car control buttons shall be illuminated.
-
11B-407.4.6.2.2 Arrangement
Buttons shall be arranged with numbers in ascending order. When two or more columns of buttons are provided they shall read from left to right.
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum. Top of support rails shall be 31 inches (787 mm) minimum to 33 inches (838 mm) maximum above...
-
11B-411.4.7.4 Button spacing
Button spacing shall comply with Section 11B-407.4.7.1.5.
-
407.2.2 Hall Signals
Hall signals, including in-car signals, shall comply with 407.2.2.
-
11B-407.4.6.2.1 Size and shape
Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding...
-
11B-411.4.7.1 Type
Control button type shall comply with Section 11B-407.4.7.1.1.
-
11B-407.2.2 Hall signals
Hall signals, including in-car signals, shall comply with Section 11B-407.2.2.
-
407.4.7.1 Buttons
Car control buttons shall comply with 407.4.7.1.
-
11B-407.4.10.2 Surfaces
Support rails shall be smooth and any surface adjacent to them shall be free of sharp or abrasive elements.
-
407.4.6.2.1 Size
Buttons shall be ¾ inch (19 mm) minimum in their smallest dimension.
-
407.4.6.2.2 Arrangement
Buttons shall be arranged with numbers in ascending order. When two or more columns of buttons are provided they shall read from left to right.
-
11B-411.4.6.1 Location
Controls shall be located within one of the reach ranges specified in Section 11B-308.
-
4.10.10 Floor Surfaces
Floor surfaces shall comply with 4.5.
-
4.1.6(1)(k) EXCEPTION
(k) EXCEPTION:
-
4.10.4(1)
(1) Hall lantern fixtures shall be mounted so that their centerline is at least 72 in (1830 mm) above the lobby floor. (See Fig. 20.)
